Subaru Crosstrek Service Manual: Wiring system
- Basic diagnostic procedure
- Basic procedures
- Connector symbol in wiring harness
- Basic inspection
- How to read wiring diagrams
- Symbols in wiring diagrams
- Abbreviation in wiring diagrams
- Working precautions
- Precautions when working with the parts mounted on the vehicle
- Precautions in trouble diagnosis and repair of electric parts
- Air conditioning system Wiring diagram
- Airbag system Wiring diagram
- Antenna cord Location
- Audio system Wiring diagram
- Back-up light system Wiring diagram
- Blind spot detection/rear cross traffic alert Wiring diagram
- Bulkhead wiring harness (in compartment) Location
- Bulkhead wiring harness (in engine compartment) Location
- Can communication system Wiring diagram
- Charging system Wiring diagram
- Clearance light and illumination light system Wiring diagram
- Combination meter system Wiring diagram
- Coolant temperature system Wiring diagram
- Cruise control system Wiring diagram
- Cvt control system Wiring diagram
- Door cord Location
- Electric power steering system Wiring diagram
- Engine electrical system Wiring diagram
- Engine wiring harness and transmission cord Location
- Eyesight system Wiring diagram
- Front accessory power supply socket system Wiring diagram
- Front fog light system Wiring diagram
- Front wiper and washer system Wiring diagram
- Front wiring harness Location
- Fuel gauge system Wiring diagram
- Ground circuit Wiring diagram
- Harness components location Location
- Headlight beam leveler system Wiring diagram
- Headlight system Wiring diagram
- Horn system Wiring diagram
- Immobilizer system Wiring diagram
- Instrument panel wiring harness Location
- Interior light system Wiring diagram
- Keyless access system Wiring diagram
- Keyless entry system Wiring diagram
- Multi-function display (mfd) system Wiring diagram
- Navigation system Wiring diagram
- Occupant detection system Wiring diagram
- Oil pressure warning light system Wiring diagram
- Parking brake / brake fluid level warning light system Wiring diagram
- Power supply circuit Wiring diagram
- Power window system Wiring diagram
- Push button start system Wiring diagram
- Radiator fan system Wiring diagram
- Rear accessory power supply socket system Wiring diagram
- Rear defogger system Wiring diagram
- Rear wiper and washer system Wiring diagram
- Rear wiring harness Location
- Rear wiring harness and rear gate cord Location
- Rearview camera system Wiring diagram
- Rearview mirror system Wiring diagram
- Remote control mirror system Wiring diagram
- Remote engine start system Wiring diagram
- Seat belt warning system Wiring diagram
- Seat heater system Wiring diagram
- Security system Wiring diagram
- Shift lock control system Wiring diagram
- Speedometer system Wiring diagram
- Starter system Wiring diagram
- Stop light system Wiring diagram
- Sunroof control system Wiring diagram
- Telematics system Wiring diagram
- Tire pressure monitoring system Wiring diagram
- Turn signal light and hazard light system Wiring diagram
- Vehicle dynamics control system Wiring diagram
- Wiper deicer system Wiring diagram
Installation
WIPER AND WASHER SYSTEMS > Wiper BladeINSTALLATION1. Install each part in the reverse order of removal.2. Confirm that the clip is locked securely. ...
Other materials:
Inspection
SECURITY AND LOCKS > Keyless Access Outdoor AntennaINSPECTION1. Check the setting by performing Keyless access system check using the Subaru Select Monitor. Keyless Access System Check > OPERATION">2. Disconnect the Subaru Select Monitor. While bringing the access key, operate the tou ...
Dtc b1572 imm circuit except antenna circuit
IMMOBILIZER (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B1572 IMM CIRCUIT EXCEPT ANTENNA CIRCUITDTC detecting condition:Communication failure between body integrated unit and ECMCAUTION:When the body integrated unit is replaced, registration of the immobilizer syste ...
Preparation for maintenance settings
1. Turn the ignition switch to the "ON"
position.
2. Push and hold the
button to show
the selection screen.
3. After the selection screen is displayed,
operate the "
" or "
" switch to show the
"Maintenance" item. Then, push the
button. ...
