Subaru Crosstrek Service Manual: Abbreviation in wiring diagrams
WIRING SYSTEM > Basic Diagnostic Procedure
ABBREVIATION IN WIRING DIAGRAMS
Abbr. | Full name |
ABS | Anti-lock Brake System |
ACC | Accessory |
A/C | Air Conditioner |
ASSY | Assembly |
AT | Automatic Transmission |
A/F | Air/Fuel (air fuel ratio sensor) |
ATF | Automatic Transmission Fluid |
AUX | Auxiliary Audio Input Terminal |
AWD | All Wheel Drive |
B, BAT | Battery |
BSD/RCTA | Blind Spot Detection/Rear Cross Traffic Alert |
CAN | Controller Area Network |
CM | Control Module |
CVT | Continuously Variable Transmission |
D | Drive range or Down |
DN | Down |
E | Ground |
ELCM | Evaporative Leak Check Module |
ECO | Economy |
ECM | Engine Control Module |
EEPROM | Electrically Erasable Programmable Read-Only Memory |
EGR | Exhaust Gas Recirculation |
F/B | Fuse & Relay Box |
FL | Front Left |
FR | Front Right |
G | Gravity (G sensor) |
H/L | Headlight |
HI | High |
I/F | Interface |
IG | Ignition |
INT | Intermittent |
ISO | International Organization for Standardization |
J/C | Joint Connector |
LCD | Liquid Crystal Display |
LH | Left Hand |
LO | Low |
LWR | Lower |
M | Motor |
M/B | Main Fuse Box |
MFD | Multi Function Display |
MT | Manual Transmission |
N | Neutral Range |
NAVI | Navigation |
OP | Open or Optional Parts |
P | Parking or Parking range |
PASS | Passing |
PCV | Positive Crankcase Ventilation Valve |
R | Reverse Range |
RH | Right Hand |
RL | Rear Left |
RR | Rear Right |
SBF | Slow Blow Fuse |
SRF | Steering responsive fog light |
ST | Starter |
SW | Switch |
TCM | Transmission Control Module |
TEL | Telephone |
TFT | Thin Film Transistor |
TPMS | Tire Pressure Monitor System |
UPR | Upper |
VDC | Vehicle Dynamics Control |
WASH | Washer |
Symbols in wiring diagrams
WIRING SYSTEM > Basic Diagnostic ProcedureSYMBOLS IN WIRING DIAGRAMSA number of symbols are used in each wiring diagram to easily identify parts or circuits.1. RELAYA symbol used to indicate a rela ...
Other materials:
Installation
CLUTCH SYSTEM > Clutch PedalINSTALLATION1. Install in the reverse order of removal.CAUTION:Always use a new clevis pin.Tightening torque:Clutch pedal18 N·m (1.8 kgf-m, 13.3 ft-lb)Knee airbag module7.5 N·m (0.76 kgf-m, 5.5 ft-lb)Air intake boot3 N·m (0.3 kgf-m, 2.2 ft-lb)2. Ad ...
Inspection
LIGHTING SYSTEM > Day Time Running ResistorINSPECTION1. Measure the resistance between connector terminals.Preparation tool:Circuit testerTerminal No.Inspection conditionsSpecificationConnection diagram1 — 2Always1.13±0.05 ?2. Replace the resistor assembly - daytime running light if the inspec ...
Removal
EXTERIOR BODY PANELS > Rear GateREMOVALCAUTION:The panel - rear gate is heavy. When removing and installing it, always work in a team of two or more persons.1. REAR GATE PANEL1. Disconnect the ground cable from battery. NOTE">2. Remove the trim panel - rear gate. Rear Gate Trim > REM ...
