WIRING SYSTEM > Bulkhead Wiring Harness (In Compartment)
LOCATION
Connector | Connecting to | ||||
No. | Pole | Color | Area | No. | Description |
B27 | 4 |
| B-4 | Blower Resistor (manual A/C) | |
B30 | 8 | Black | C-5 | Front door cord RH | |
B31 | 10 | Gray | C-1 | AB1 | Airbag wiring harness |
B32 | 8 |
| B-2 | Turn signal and hazard unit | |
B40 | 16 | Black | C-1 | Data link connector | |
B41 | 2 |
| C-2 | Power window circuit breaker | |
B52 | 24 |
| D-1 | F/B | |
B54 | 48 | Black | B-2 | TCM | |
B57 | 4 |
| B-4 | Power transistor (auto A/C) | |
B65 | 4 |
| B-2 | Stop light and brake switch | |
B68 | 14 |
| B-3 | Roll connector | |
B70 | 10 |
| B-3 | Combination switch | |
B71 | 20 |
| B-3 | ||
B72 | 6 |
| C-3 | Ignition switch | |
B77 | 6 |
| C-4 | Mode door actuator (auto A/C) | |
B83 | 8 |
| B-4 | J/C | |
B87 | 2 |
| B-5 | Blower motor | |
B88 | 2 | Brown | C-4 | Evaporator sensor (auto A/C) | |
3 |
| C-4 | Evaporator sensor (manual A/C) | ||
B89 | 2 | Black | B-5 | Blower diode | |
B90 | 20 |
| B-5 | R50 | Roof cord |
B92 | 20 |
| D-1 | R5 | Rear wiring harness LH |
B97 | 20 |
| C-5 | R1 | Rear wiring harness RH |
B99 | 20 |
| D-1 | R3 | Rear wiring harness LH |
B101 | 8 | Black | C-1 | Front door cord LH | |
B106 | 2 |
| C-3 | Clutch start switch | |
B107 | 2 | Blue | C-3 | Clutch switch | |
B116 | 8 |
| C-4 | AT select lever | |
B122 | 8 |
| B-5 | J/C | |
B123 | 2 | Black | C-1 | B124 | Key lock |
B124 | 2 | Black | C-1 | B123 | |
B134 | 34 |
| C-4 | ECM | |
B135 | 35 |
| C-5 | ||
B136 | 35 |
| C-5 | ||
B137 | 31 |
| C-5 | ||
B150 | 24 |
| C-1 | Auto headlight beam leveler CM | |
B151 | 6 |
| B-5 | R430 | Roof cord |
B152 | 10 | Gray | D-1 | F/B | |
B158 | 8 |
| D-1 | ||
B159 | 9 | Brown | D-2 | ||
B162 | 2 |
| D-2 | ||
B163 | 6 | Black | B-5 | Intake door actuator | |
B180 | 4 |
| C-2 | Remote engine start CM (without push button start) | |
8 |
| C-2 | Remote engine start CM (with push button start) | ||
B181 | 2 |
| C-2 | B182 | Bulkhead wiring harness |
B182 | 2 |
| C-2 | B181 | |
B220 | 44 |
| B-5 | Relay holder | |
B225 | 44 |
| C-2 | ||
B229 | 8 |
| B-1 | AD1 | Telematics button adapter cord |
B231 | 5 |
| B-3 | Steering angle sensor | |
B235 | 6 |
| C-4 | Air mix door actuator LH (with left/right independent air conditioner) | |
B239 | 6 |
| B-4 | Air mix door actuator (without left/right independent air conditioner) | |
Air mix door actuator RH (with left/right independent air conditioner) | |||||
B280 | 34 |
| C-1 | Body integrated unit | |
B281 | 35 |
| C-2 | ||
B315 | 6 | Black | C-4 | Accelerator pedal position sensor | |
B358 | 2 |
| C-4 | AT select lever illumination | |
B367 | 8 |
| C-2 | Impact sensor | |
B386 | 4 |
| B-5 | Blower motor relay | |
B415 | 7 | Black | C-3 | Immobilizer antenna | |
B422 | 5 |
| B-3 | ID code box | |
B424 | 7 | Black | C-3 | Steering lock CM | |
B426 | 4 | Black | C-2 | Accessory relay | |
B475 | 4 |
| D-1 | Wiper relay unit | |
B550 | 20 |
| D-2 | Fuse holder | |
B551 | 12 |
| C-2 | i229 | Instrument panel wiring harness LH |
B552 | 17 | Gray | C-2 | i230 | |
B553 | 20 |
| D-2 | i231 | |
B555 | 2 |
| C-3 | Key warning switch | |
B556 | 2 |
| C-4 | AB65 | Airbag wiring harness |
B557 | 2 |
| C-3 | Key lock solenoid | |
B558 | 7 |
| B-3 | Combination switch | |
B559 | 5 |
| B-3 | Security CM | |
B572 | 18 |
| C-2 | Keyless access CM | |
B573 | 28 |
| C-2 | ||
B574 | 30 |
| C-2 | ||
B575 | 22 |
| C-1 | B576 | Bulkhead wiring harness |
B576 | 22 |
| C-1 | B575 | |
B577 | 10 |
| C-1 | B578 | |
B578 | |||||
Blind spot detection/rear cross traffic alert Wiring diagram
Bulkhead wiring harness (in engine compartment) LocationRemoval
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Automatic Transmission AssemblyREMOVAL1. Disconnect the ground cable from battery. NOTE">NOTE:For model with battery sensor, disconnect the ground terminal from battery sensor.2. Remove the clip (A) from the air intake boot.3. Loosen the clamp ...
Removal
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > CVTF FilterREMOVALNOTE:• Although CVTF filter is a maintenance-free part, replace it if a large quantity of wear debris and metal particles are found in CVTF and CVTF filter.• For removal of CVTF filter, refer to “Transmission Case&rdq ...
Inspection
LIGHTING SYSTEM > Spot Map LightINSPECTION1. SPOT MAP LIGHT BULB1. Visually check the bulb for blow out.2. Check the bulb specification. General Description > SPECIFICATION">3. Replace the bulb if it is found defective.2. SPOT MAP LIGHT SWITCH1. Check the resistance between switch ter ...