Subaru Crosstrek Service Manual: Dtc p0512 starter (switch) request circuit
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)
DTC P0512 STARTER (SWITCH) REQUEST CIRCUIT
DTC detecting condition:
Immediately at fault recognition
Trouble symptom:
Failure of engine to start
CAUTION:
After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">
, and Inspection Mode Inspection Mode > PROCEDURE">.
Wiring diagram:
Engine electrical system Engine Electrical System > WIRING DIAGRAM">
| STEP | CHECK | YES | NO |
1.CHECK PUSH BUTTON IGNITION SWITCH.
Operate the push button ignition switch.
Does it operate smoothly without catch?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0512 STARTER (SWITCH) REQUEST CIRCUIT">Go to Step 2.
Replace the push button ignition switch. Push Button Ignition Switch">
2.CHECK DTC.
1) Clear the memory using the Subaru Select Monitor. Clear Memory Mode">
2) Start and idle the engine for three minutes or more.
Is the same DTC as current diagnosis output?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0512 STARTER (SWITCH) REQUEST CIRCUIT">Go to Step 3.
Even if DTC is detected, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.
NOTE:
In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.
3.CHECK HARNESS BETWEEN ECM AND KEYLESS ACCESS CM.
1) Turn the ignition to OFF.
2) Disconnect the connector from ECM.
3) Turn the ignition to ON.
4) Measure the voltage between ECM connector and chassis ground.
Connector & terminal
(B137) No. 17 (+) — Chassis ground (−):
Is the voltage 10 V or more?
Repair the short circuit to power supply in harness between ECM connector and keyless access CM connector.
Repair the poor contact of ECM connector.
1. OUTLINE OF DIAGNOSIS
Detect abnormal continuity in the starter SW1.
Judge as ON NG when the starter SW 1 signal remains ON.
2. EXECUTION CONDITION
Secondary parameters | Execution condition |
Battery voltage | ≥ 8 V |
Engine speed | ≥ 500 rpm |
3. GENERAL DRIVING CYCLE
Perform the diagnosis continuously after starting the engine.
4. DIAGNOSTIC METHOD
If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.
Malfunction Criteria | Threshold Value |
Starter SW1 voltage | ≥ Battery voltage ? 0.85 |
Time Needed for Diagnosis: 30000 ms
Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.
Dtc p050b cold start ignition timing performance
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P050B COLD START IGNITION TIMING PERFORMANCENOTE:For the diagnostic procedure, refer to DTC P050A. Diagnosti ...
Dtc p0604 internal control module random access memory (ram) error
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0604 INTERNAL CONTROL MODULE RANDOM ACCESS MEMORY (RAM) ERRORDTC DETECTING CONDITION:Immediately at fault re ...
Other materials:
Dtc p0705 transmission range sensor "a" circuit (prndl input)
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0705 TRANSMISSION RANGE SENSOR "A" CIRCUIT (PRNDL INPUT)DTC detecting condition:Immediately at fault recognitionTrouble symptom:• Shift characteristics are erroneous.&bul ...
Installation
AIRBAG SYSTEM > Curtain Airbag ModuleINSTALLATIONCAUTION:• Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">• When installing the curtain airbag ...
Center information display (CID)
WARNING
While operating the center information display in the Subaru Ascent, always
maintain full attention to driving conditions. If interacting with the display interferes
with your concentration, safely stop the vehicle before making any adjustments.
Looking at the screen for extended peri ...
