Subaru Crosstrek Service Manual: Keyless access with push button start system (diagnostics)
- Control module i/o signal
- Diagnostic procedure with diagnostic trouble code (dtc)
- Dtc u0100 lost communication with ecm/pcm a
- Dtc u1120 lost communication with autostart stop control module
- Dtc u0101 lost communication with tcm
- Dtc b1242 wireless tuner
- Dtc b2271 ign relay control circuit
- Dtc b2274 acc relay control circuit
- Dtc b2275 engine start request control circuit
- Dtc b2276 acc relay off signal
- Dtc u0122 lost communication with vehicle dynamics control module
- Dtc u0140 lost communication with body control module
- Dtc b2277 submerging circuit
- Dtc b2282 vehicle speed signal correlation
- Dtc b2283 vehicle speed sensor
- Dtc b2284 brake signal correlation
- Dtc b2285 steering lock position signal correlation
- Dtc b2286 engine speed signal(without auto start stop)
- Dtc b228a engine speed signal(with auto start stop)
- Dtc b2779 remote control engine starter collation
- Dtc b2781 steering lock cm control circuit
- Dtc b2782 steering lock drive request signal correlation
- Dtc b2784 antenna circuit (push engine switch)
- Dtc b2785 lin communication
- Dtc b2786 steering lock cm communication
- Dtc b2788 ign signal correlation (steering lock cm)
- Dtc b2789 id code box communication
- Dtc b2790 id code box circuit
- Dtc b278a push engine switch power supply circuit
- Dtc b278d id code box judgment circuit
- Dtc b27a1 driver side external antenna open
- Dtc b27a2 passenger side external antenna open
- Dtc b27a5 front internal antenna open
- Dtc b27a7 trunk/rear gate internal antenna open
- Dtc b27a8 trunk/rear gate external antenna open
- Dtc b1572 imm circuit except antenna circuit
- Dtc b1576 egi control module eeprom
- Dtc b1577 imm control module eeprom
- Dtc b1571 reference code incompatibility (immobilizer cm to ecm)
- Dtc u0155 lost communication with instrument panel cluster (ipc) control module
- Dtc u0401 invalid data received from ecm/pcm a
- Dtc u0422 invalid data received from body control module
- Dtc u0073 control module communication bus off
- General description
- Read current data
- Subaru select monitor
- Basic diagnostic procedure Procedure
- Check list for interview Check
- Clear memory mode Operation
- Diagnostics with phenomenon Inspection
- Electrical component location Location
- General diagnostic table Inspection
- Keyless access system check Operation
- List of diagnostic trouble code (dtc) List
- Read diagnostic trouble code (dtc) Operation
- System operation check mode Operation
Component
INTAKE (INDUCTION)(H4DO) > General DescriptionCOMPONENT(1)Air intake duct(8)Air cleaner case (rear)Tightening torque: N·m (kgf-m, ft-lb)(2)Clip(9)ClipT1:1 (0.1, 0.7)(3)Cushion(10)Mass air fl ...
Other materials:
Location
CONTROL SYSTEMS > AT Shift Lock Control SystemLOCATION1. MODEL WITHOUT PUSH BUTTON IGNITION SWITCH(1)TCM (“P” range)(4)Key cylinder (with built-in key warning switch)(6)“P” range switch(2)Body integrated unit(5)Solenoid unit(7)Key lock solenoid(3)Stop light and brake switc ...
Airflow mode selection
To select the airflow mode:
Type A, B and C: Turn the airflow mode
selection dial.
Type D: Press the airflow mode selection
button.
To select the defrost mode:
Type A and B: Turn the airflow mode
selection dial.
Type C and D: Press the defroster button.
Airflow modes are as follows. ...
Power steering warning light
This
warning light illuminates when the
ignition switch is turned to the "ON"
position and turns off after the engine
has started. This indicates that the warning
system is working properly.
While the engine is running, this warning
light illuminates when a malfunction has
been detected ...
