Subaru Crosstrek Service Manual: System operation check mode Operation

Subaru Crosstrek Service Manual / Keyless access with push button start system (diagnostics) / System operation check mode Operation

KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > System Operation Check Mode

OPERATION

1. On «Start» display, select «Diagnosis».

2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».

3. On «Main Menu» display, select «Each System».

4. On «Select System» display, select «Keyless Access with Push Button Start» and then select «Enter».

5. On «Select Function» display, select «Active Test».

6. Select a location to be inspected.

NOTE:

Each output check continues to run for five seconds before stopping automatically.

Data	Keyless access CM output check	Remarks
Tuner power supply ON (indoor tuner)	Output	Perform the power supply check for the receiver.
Tuner power supply ON (indoor tuner)	Stop	Perform the power supply check for the receiver.
Driver’s external transmitter	Output	Perform the output check for the driver’s side door outside antenna.
Driver’s external transmitter	Stop
Passenger’s external transmitter	Output	Perform the output check for the passenger’s side door outside antenna.
Passenger’s external transmitter	Stop
STSW	Output	Turn on the STSW. *2
STSW	Stop	Turn on the STSW. *2
IGN2	Output	Turn on the IGN2.
IGN2	Stop	Turn on the IGN2.
IGN1	Output	Turn on the IGN1.
IGN1	Stop	Turn on the IGN1.
ACC	Output	Turn on the ACC.
ACC	Stop	Turn on the ACC.
Start SW character illumination lighted	Output	Perform ON output of the push button ignition switch back-up light. *1
Start SW character illumination lighted	Stop
Start SW indicator lighted (green)	Output	Perform ON output of the push button ignition switch back-up light. *1
Start SW indicator lighted (green)	Stop
Start SW indicator lighted (orange)	Output	Perform ON output of the push button ignition switch back-up light. *1
Start SW indicator lighted (orange)	Stop
Steering lock power supply	Output	Output power supply signal from power supply CM to steering lock CM.
Steering lock power supply	Stop

*1: When lit by a condition other than for a system operation check mode, it will not become unlit even when set to OFF or no output.

*2: When performed with ignition switch ON, engine will start. Therefore, great care must be exercised.

NOTE:

For detailed operation procedures, refer to “Application help”.

Read diagnostic trouble code (dtc) Operation

KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > Read Diagnostic Trouble Code (DTC)OPERATION1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the ...

Lan system (diagnostics)

...

Other materials:

Dtc b1642 side satellite sensor bus rh lost communication
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B1642 SIDE SATELLITE SENSOR BUS RH LOST COMMUNICATIONDiagnosis start condition:Ignition voltage is 10 V to 16 V.DTC detecting condition:• Open or short circuit in harness of side sensor bus (RH)• Side airbag sensor (R ...

Dtc b2271 ign relay control circuit
KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2271 IGN RELAY CONTROL CIRCUITDTC detecting condition:• When malfunction is detected in IG1 and IG2 drive circuits in the keyless access CM.• When malfunction is de ...

Driver's seatbelt
The driver's seatbelt has a shoulder belt pretensioner. The pretensioner sensor also serves as follows. SRS frontal airbag sensor Side impact sensor Front door impact sensor Rollover sensor If the sensor detects a certain predetermined amount of force during frontal or side col ...