Subaru Crosstrek Service Manual: Hvac system (auto a/c) (diagnostics)
- Auto a/c control module i/o signal
- Diagnostic procedure with diagnostic trouble code (dtc)
- Dtc u0100 lost communication with ecm/pcm a
- Dtc u0073 control module communication bus off
- Dtc u0101 lost communication with tcm
- Dtc u0122 lost communication with vehicle dynamics control module
- Dtc u0140 lost communication with body control module
- Dtc b1430 in-vehicle (post evaporator) temperature sensor circuit open
- Dtc b1431 in-vehicle (post evaporator) temperature sensor circuit short-circuit
- Dtc b1432 ambient temperature sensor circuit open (air-conditioner)
- Dtc b1433 ambient temperature sensor circuit short-circuit (air-conditioner)
- Dtc b1434 evaporator temperature sensor circuit open
- Dtc b1435 evaporator temperature sensor circuit short-circuit
- Dtc b14a1 sunload sensor circuit low/open
- Dtc b14a2 sunload sensor circuit short-circuit
- Dtc b14e1 air mix door actuator stepping motor circuit open (driver)
- Dtc b14e2 air mix door actuator stepping motor circuit short-circuit (driver)
- Dtc b14e3 air mix door actuator stepping motor circuit open (passenger)
- Dtc b14e4 air mix door actuator stepping motor circuit short-circuit (passenger)
- Dtc b14e5 mode door actuator stepping motor circuit open
- Dtc b14e6 mode door actuator stepping motor circuit short-circuit
- Dtc b14e9 intake door actuator circuit open
- Dtc b14ea intake door actuator circuit short-circuit
- Dtc b14eb intake door actuator stuck
- Dtc u0155 lost communication with instrument panel cluster (ipc) control module
- Dtc u0401 invalid data received from ecm/pcm a
- Dtc u0402 invalid data received from tcm
- Dtc u0416 invalid data received from vehicle dynamics control module
- Dtc u0422 invalid data received from body control module
- Dtc u0423 invalid data received from instrument panel cluster control module
- Diagnostics with phenomenon
- General description
- Read current data
- Basic diagnostic procedure Procedure
- Clear memory mode Operation
- Diagnostic procedure for subaru select monitor communication Communication for initializing impossible
- Electrical component location Location
- List of diagnostic trouble code (dtc) List
- Read diagnostic trouble code (dtc) Operation
- Subaru select monitor Operation
Repair
GLASS/WINDOWS/MIRRORS > Wiper Deicer SystemREPAIRRefer to “REPAIR” of “Rear Window Defogger System”. Rear Window Defogger System > REPAIR">NOTE:Heat wire repair ...
Other materials:
Basic diagnostic procedure Procedure
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Basic Diagnostic ProcedurePROCEDURESTEPCHECKYESNO1.PERFORM CUSTOMER INTERVIEW.Using the Check List for Interview, ask the customer the condition of how trouble occurs.Did you interview the customer? Basic Diagnostic Procedure > PROC ...
Removal
FRONT SUSPENSION > Front StrutREMOVAL1. Lift up the vehicle, and then remove the front wheels.2. Remove the front strut assembly.(1) Place an alignment mark (a) on the adjusting bolt and the strut.(2) Remove the brake hose bracket.(3) Remove the clamp of ABS wheel speed sensor harness.(4) Remove ...
Dtc p0016 crankshaft position - camshaft position correlation bank 1 sensor a
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0016 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 1 SENSOR ADTC detecting condition:Detected when two consecutive driving cycles with fault occur.Trouble symptom:• Engine stall• Improp ...
