Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: User customizing Operation

BODY CONTROL SYSTEM (DIAGNOSTICS) > User Customizing

OPERATION

1. On «Start» display, select «Diagnosis».

2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».

3. On «Main Menu» display, select «Each System».

4. On «Select System» display, select «Body Control» and then select «Enter».

5. On «Select Function» display, select «Customize».

NOTE:

If not equipped (depending on destination area or vehicle equipment condition), customizing is not possible.

For detailed operation procedures, refer to “Application help”.

List of User Customizing item

Data

Initial setting value

Customize setting

Remarks

Off delay time

30 Sec

OFF

Room light off delay time can be selected.

10 Sec

20 Sec

30 Sec

Auto Light Sensitivity Adjustment

Normal

Dull

Slow response

Normal

Standard

Sensitive

Quick response

Very sensitive

Fairly quick response

Power rear gate setting

—

(*1)

ON

Fixed at OFF because this is not applicable.

OFF

Lane change signal setting

ON

ON

One-touch blinker control is performed.

OFF

One-touch blinker control is not performed.

Rear wiper auto setting

—

ON

Existence of rear wiper linked with reverse operation can be set.

OFF

TPMS Setting

—

(*1)

TPMS

Set to “ON” for model with TPMS.

No TPMS

Driver’s Door Unlock Setting

Selection

Selection

The door to be unlocked when you touch the driver’s door can be set.

ALL

Rear Gate Unlock Setting

Selection

Selection

The door to be unlocked when you touch the rear gate switch can be set.

ALL

One-touch Turn Signal System Setup

ON

ON

ON/OFF of the one-touch blinker can be set.

OFF

Auto Wiper System (Rear) Setup

OFF

ON

ON/OFF of the rear wiper linked with reverse operation can be set.

OFF

Steering Responsive Fog Lamp Setting

OFF

ON

SRF control is performed.

OFF

SRF control is not performed.

Rear defogger operation mode

Normal

Normal

Automatically stops in 15 minutes after the switch is turned to ON.

Continuous

Repeats activated for 15 minutes and deactivated for 2 minutes until the switch is turned to OFF.

Security Alarm Setup

ON

ON

Security alarm (hazard, horn or siren) becomes activated.

OFF

Security alarm becomes deactivated.

Impact Sensor Setup

OFF

ON

Workable when the Impact Sensor Setup is set to “ON”. Impact sensor function becomes activated.

OFF

Impact sensor function becomes deactivated. (Be sure to set to “OFF” for models without sensors.)

Alarm delay setup

ON

After the keyless lock operation, the alarm monitor starts after the following delay time has passed.

ON

Delay time is 30 seconds.

OFF

Delay time is 0 second.

Lockout prevention

ON

ON

key lockout prevention function is activated. (The function does not operate if safety knob is locked by hand.)

OFF

Key lockout prevention function is deactivated.

Impact sensor (OP)

OFF

ON

Vehicle is controlled in impact sensor equipped mode. (Make sure to set to “OFF” for models without the impact sensor. When “ON”, hazard, horn or siren become activated by keyless lock (alarm monitor start).)

OFF

Vehicle is controlled in impact sensor non-equipped mode.

Buzzer sounding setting

ON

ON

Buzzer operates when lock/unlock is selected by keyless entry system operation.

OFF

Buzzer does not operate when lock/unlock is selected by keyless entry system operation.

Abnormal warning lamp flashing setting

ON

ON

Hazard blinks when lock/unlock is selected by keyless entry system operation.

OFF

Hazard is not interlocked when lock/unlock is selected by keyless entry system operation.

Passive Alarm

OFF

ON

OFF

Door open warning

ON

ON

OFF

Dome Light Alarm Setting

OFF

ON

Room light illuminates interlocking with alarm.

OFF

Room light does not illuminate interlocking with alarm.

Auto A/C ECU Setting

—

(*1)

ON

Diagnoses with auto A/C CM.

OFF

Diagnoses without auto A/C CM.

Wiper Deicer setting

—

(*1)

ON

Wiper deicer control is performed.

OFF

Wiper deicer control is not performed.

Illumination Control On/Off

ON

ON

OFF

Sedan/Wagon Setting

—

(*1)

Sedan

Body control is performed for Sedan.

Wagon

Body control is performed for Wagon.

MT/AT Setting

—

(*1)

MT

Body control is performed for MT.

AT

Body control is performed for AT.

Illumination Sensor Setting

—

(*1)

ON

Set to “ON” for model with auto light.

OFF

Factory initial setting

Market

Market

Customize setting is reset when mode is switched from Market to Factory.

Factory

Welcome Light (Exit)

30 Sec

OFF

Length of the lighting time can be set.

30 Sec

60 Sec

90 Sec

Welcome Light Off Delay Time(Approaching)

30 Sec

OFF

Length of the lighting time can be set.

30 Sec

60 Sec

90 Sec

Keyless Buzzer Volume

5

1 — 7

Buzzer volume can be set.

NOTE:

*1: Customization item according to the actual vehicle equipment

6. When the setting is complete, see «Data monitor» to make sure that the alterations are consistent with the actual equipment on the vehicle.

CAUTION:

the above settings must match the actual vehicle equipment.

Do not change settings except for setting above while setting the functions.

Be sure not to change Factory initial setting except when installing a new body integrated unit.

Registration body integrated unit Operation
BODY CONTROL SYSTEM (DIAGNOSTICS) > Registration Body Integrated UnitOPERATION1. CONFIRM CURRENT SETTING1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the ...

Brake
...

Other materials:

List
TELEMATICS SYSTEM (DIAGNOSTICS) > Read Current DataLISTDisplayContentReference valueUnitTrip Count [count]Refer to “LAN SYSTEM (DIAGNOSTICS)”. General Description > CAUTION"> — — Count — — Time Count [msec] — — Current GPS DataCurrent GPS information — †...

Dtc u0424 invalid data received from hvac control module
LAN SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0424 INVALID DATA RECEIVED FROM HVAC CONTROL MODULEDTC DETECTING CONDITION:Defective data was transmitted from A/C control panel.TROUBLE SYMPTOM:Cooperation control of air conditioner does not operate properly. ...

Dtc p0031 a/f / o2 heater control circuit low bank 1 sensor 1
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0031 A/F / O2 HEATER CONTROL CIRCUIT LOW BANK 1 SENSOR 1DTC DETECTING CONDITION:Immediately at fault recognitionCAUTION:After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode ...

© 2016-2024 Copyright www.sucross.com