Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Registration body integrated unit Operation

Subaru Crosstrek Service Manual / Body control system (diagnostics) / Registration body integrated unit Operation

BODY CONTROL SYSTEM (DIAGNOSTICS) > Registration Body Integrated Unit

OPERATION

1. CONFIRM CURRENT SETTING

1. On «Start» display, select «Diagnosis».

2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».

3. On «Main Menu» display, select «Each System».

4. On «Select System» display, select «Body Control» and then select «Enter».

5. On «Select Function» display, select «Customize».

6. Save the setting.

Required items for new registration. (Except for system not equipped)

Item

Item to confirm

Remarks

number of regist.

1

2

3

4

Number of registered ID

Off delay time

OFF

10 Sec

20 Sec

30 Sec

Setting for lighting off time

Auto Light Sensitivity Adjustment

Dull

Normal

(Standard)

Sensitive

Very sensitive

1st (slow) — 4th (fairly quick)

Power rear gate setting

ON

OFF

N/A

Lane change signal setting

ON

OFF

Rear wiper auto setting

ON

OFF

TPMS Setting

TPMS

No TPMS

Driver’s Door Unlock Setting

ALL

Selection

Rear Gate Unlock Setting

ALL

Selection

One-touch Turn Signal System Setup

ON

OFF

Auto Wiper System (Rear) Setup

ON

OFF

Steering Responsive Fog Lamp Setting

ON

OFF

Rear defogger operation mode

Normal

Continuous

Security Alarm Setup

ON

OFF

Impact Sensor Setup

ON

OFF

Option setting

Alarm delay setup

ON

OFF

Lockout prevention

ON

OFF

Impact sensor

ON

OFF

Option setting

Buzzer sounding setting

ON

OFF

Abnormal warning lamp flashing setting

ON

OFF

Passive Alarm

ON

OFF

Door open warning

ON

OFF

Dome Light Alarm Setting

ON

OFF

Auto A/C ECU Setting

ON

OFF

Wiper Deicer setting

ON

OFF

Option setting

Illumination Control On/Off

ON

OFF

Sedan/Wagon Setting

WAGON

SEDAN

MT/AT Setting

MT

AT

Illumination Sensor Setting

ON

OFF

Factory initial setting

Factory

Market

Do not change to factory mode.

Welcome Light (Exit)

OFF

30 Sec

60 Sec

90 Sec

Welcome Light Off Delay Time(Approaching)

OFF

30 Sec

60 Sec

90 Sec

Keyless Buzzer Volume

1 2 3 4 5 6 7

2. REGISTRATION BODY INTEGRATED UNIT (FUNCTION SETTING)

CAUTION:

For the body integrated unit, function selection is available to control the entire vehicle systems. It is possible to control the original functions of vehicle when registrations of body integrated unit and function setting are corresponded to vehicle equipment.

If registrations and function setting are different from vehicle equipment, vehicle system does not operate normally and diagnosis cannot be performed correctly. Pay attention to following item.

Be sure to correspond registrations, or User Customizing settings to vehicle equipment.

Do not change the settings of vehicle improperly.

Make sure that the key illumination does not blink with ignition switch ON, or that the body integrated unit registration item “Factory initial setting” is set to “Market”. If “Factory initial setting” is set to “Factory”, key illumination blinks when the ignition switch is turned ON, to notify that the settings are not confirmed. (Except for model with the keyless access with push button start system)

Key illumination does not blink with ignition switch turned to ON and go off with door closed. (Except for model with the keyless access with push button start system)

Be sure to register immobilizer if body integrated unit is replaced with a new part. (Except for model with the keyless access with push button start system)

Make a registration of immobilizer when the parts related to immobilizer have been replaced. Refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume. (Except for model with the keyless access with push button start system)

1. On «Start» display, select «Diagnosis».

2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».

3. On «Main Menu» display, select «Each System».

4. On «Select System» display, select «Body Control» and then select «Enter».

5. On «Select Function» display, select «Customize».

NOTE:

For the vehicle requiring the destination setting, if the destination setting is not finished, display can not be shifted into customizing screen. Registration Body Integrated Unit > OPERATION">

6. Change the setting to the contents saved at confirmation of current setting.

CAUTION:

To perform normal operation of vehicle and diagnosis, the above settings must match the actual vehicle equipment.

When the body integrated unit is new or in Factory mode, the key illumination blinks, and user customizing is incomplete. Check the user customizing settings. (For models with keyless access with push button start system, the room light illuminates.)

Be sure not to change Factory initial setting except when installing a new body integrated unit.

NOTE:

“Factory” mode:

Body integrated unit has not been set yet. It can be recognized by key illumination blinking with ignition switch turned to ON. For model with keyless access with push button start system, it can be recognized by room light blinking with ignition switch turned to ON.

All replacement body integrated units are set to “Factory” mode. When replacing a body integrated unit, be sure to perform the registration operation.

“Market” mode:

Each settings have been set. It can be recognized by key ring illumination coming on in concocting with room light and going off with ignition switch turned to ON. For model with keyless access with push button start system, it can be recognized by room light not blinking with ignition switch turned to ON.

7. Perform the Factory initial setting. On the «Customize» display screen of Subaru Select Monitor, select the «Factory initial setting».

8. Change the mode from Factory to Market.

9. Turn the ignition switch to OFF to settle the setting.

10. Perform the User Customizing. User Customizing > OPERATION">

11. Change the system selection to «Immobilizer» on Subaru Select Monitor, and perform registration of immobilizer. (Except for model with the keyless access with push button start system)

12. Follow the procedure of the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume. (Except for model with the keyless access with push button start system)

13. For vehicles with remote engine starter, refer to “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume and perform registration of the remote engine starter. (Except for model with the keyless access with push button start system)

NOTE:

For detailed operation procedures, refer to “Application help”.

3. DESTINATION SETTING

NOTE:

For the vehicle requiring the destination setting, if the destination setting is not finished, display can not be shifted into customizing screen.

STEPCHECKYESNO

1.CONFIRM CURRENT SETTING.

Always perform confirmation of current setting before replacing the module.

Record the contents of the “Destination Setting”.

NOTE:

Refer to the “Read Current Data” and “CONFIRMATION OF CURRENT SETTING” to confirm the current setting. Registration Body Integrated Unit > OPERATION"> Read Current Data > OPERATION">

Is the current setting recorded?

Registration Body Integrated Unit > OPERATION">Go to Step 2.

Confirm the current setting. Registration Body Integrated Unit > OPERATION">Go to Step 1.

2.CONFIRM DESTINATION SETTING.

1) Connect the Subaru Select Monitor, and run the application.

2) On «Start» display, select «Diagnosis».

3) On «Vehicle selection» display, input the target vehicle information and select «Confirmed».

4) On «Main Menu» display, select «Each System».

5) On «Select System» display, select «Body Control» and then select «Enter».

6) On «Select Function» display, select «Customize».

7) The vehicle destination screen is displayed.

Is the vehicle destination setting screen displayed?

Registration Body Integrated Unit > OPERATION">Go to Step 3.

Registration Body Integrated Unit > OPERATION">Go to Step 4.

3.CONFIRM DESTINATION SETTING.

Confirm the screen displayed on Subaru Select Monitor and the actual vehicle destination.

Is it necessary to change the destination setting?

Select [Yes], Registration Body Integrated Unit > OPERATION">Go to Step 4.

Select [No], Registration Body Integrated Unit > OPERATION">Go to Step 5.

4.ENTER DESTINATION CODE.

Enter the appropriate code in the screen.

JPN: JP00

KA, KC: KA00

KS: KS00

U4, U5, U6, C6 and C0, C5 (with the keyless access with push button start system): U400

C0, C5 (without the keyless access with push button start system): C000

EK, ER: EK00

Except above: EC00

Is the appropriate code entered?

Select [OK]. Registration Body Integrated Unit > OPERATION">Go to Step 5.

Enter the destination code. Registration Body Integrated Unit > OPERATION">Go to Step 5.

5.REGISTER VEHICLE EQUIPMENT.

Customizing screen is displayed.

NOTE:

Match the each item setting of body integrated unit registration item list with the vehicle equipment.

Do all setting contents match with the vehicle equipment specification?

Registration Body Integrated Unit > OPERATION">Go to Step 6.

Change the items until each content setting match with the vehicle equipment specification. Registration Body Integrated Unit > OPERATION">Go to Step 6.

6.CONFIRM MARKET MODE.

1) Customizing screen, select the {Factory initial setting} to change the setting from “Factory” mode to “Market” mode.

2) Turn the ignition switch to OFF.

NOTE:

When the setting is changed from “Factory” mode to “Market” mode, turning the ignition switch from ON > OFF confirms the setting.

3) Turn the ignition switch to ON, and check the contents of settings.

Is the mode changed to “Market” mode?

Registration Body Integrated Unit > OPERATION">Go to Step 7.

Perform the destination setting from the first step. Registration Body Integrated Unit > OPERATION">Go to Step 1.

7.CONFIRM MARKET MODE.

Check the following.

Make sure that the “Destination Setting” in the current data display is the same as the one you confirmed in step 1.

Is the display the same as indicated?

Registration of body integrated unit is finished.

It is possible that harness malfunction may occur. Perform the diagnosis.

Read diagnostic trouble code (dtc) Operation
BODY CONTROL SYSTEM (DIAGNOSTICS) > Read Diagnostic Trouble Code (DTC)OPERATION1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle informatio ...

User customizing Operation
BODY CONTROL SYSTEM (DIAGNOSTICS) > User CustomizingOPERATION1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle information and select «Con ...

Other materials:

List of diagnostic trouble code (dtc) List
IMMOBILIZER (DIAGNOSTICS) > List of Diagnostic Trouble Code (DTC)LISTNOTE:If DTCs irrelevant to the immobilizer are detected, perform diagnosis according to the DTCs irrelevant to the immobilizer first.1. ECMDTCItemContents of diagnosisIndex No.B1570ANTENNAFaulty antenna Diagnostic Procedure with ...

Dtc b2a0c dcm internal fault
TELEMATICS SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2A0C DCM INTERNAL FAULTDIAGNOSIS START CONDITION:When ignition switch is ON.DTC DETECTING CONDITION:• Main microcomputer and communication circuit IC cannot communicate. (Defective IPC)• SIM ...

Specification
WHEEL AND TIRE SYSTEM > General DescriptionSPECIFICATION1. NOTE(1)Inset(2)P.C.D.NOTE:Size and inflation pressure of the standard equipment tire, temporary tire and appropriate tire for equipment are described on the “Tire inflation pressure” label attached to the body side of the driv ...

© 2016-2024 Copyright www.sucross.com