STARTING/CHARGING SYSTEMS(H4DO) > General Description
SPECIFICATION
Item | Specifications | ||||
Vehicle model | CVT | MT | |||
Starter | Type | Reduction type | |||
Model | M000T38571 | M000T33176 | |||
Manufacturer | Mitsubishi Electric | ||||
Voltage and output | 12 V — 1.2 kW | 12 V — 1.0 kW | |||
Direction of rotation | Counterclockwise (when observed from pinion) | ||||
Number of pinion teeth | 9 | 8 | |||
Armature commutator runout | Standard | 0.05 mm (0.0020 in) | |||
Limit | 0.10 mm (0.0039 in) | ||||
Armature depth of segment mold | Standard | 0.50 mm (0.020 in) | |||
Brush length | Standard | 12.3 mm (0.484 in) | |||
Limit | 7.0 mm (0.276 in) | ||||
Brush spring force | Standard | 15.9 — 19.5 N (1.62 — 1.99 kgf, 3.57 — 4.38 lbf) | |||
Limit | 2.5 N (0.25 kgf, 0.56 lbf) | ||||
No-load characteristics | Voltage | 11 V | |||
Current | 90 A or less | 95 A or less | |||
Generator | Type | Rotating-field three-phase type, voltage regulator built-in type, each with load response control system | |||
Model | A2TX5081 | ||||
Manufacturer | Mitsubishi Electric | ||||
Voltage and output | 12 V — 130 A | ||||
Polarity on ground side | Negative | ||||
Direction of rotation | Clockwise (when observed from pulley side) | ||||
Stator connection | 3-phase type | ||||
Output current | 1,500 r/min — 50 A or more 2,500 r/min — 111 A or more 5,000 r/min — 133 A or more | ||||
Regulated voltage | 14.1 — 14.8 V [20°C (68°F)] | ||||
Rotor slip ring outer diameter | Standard | 22.7 mm (0.894 in) | |||
Limit | 22.1 mm (0.870 in) | ||||
Brush length | Standard | 22.5 mm (0.886 in) | |||
Limit | 5.0 mm (0.197 in) | ||||
Battery | Type | 55D23L/75D23L | |||
Nominal capacity | 5 HR: 40 Ah [25°C (77°F)] (55D23L) / 5 HR: 53 Ah [25°C (77°F)] (75D23L) | ||||
Nominal voltage | 12 V | ||||
CCA | 390 A (55D23L) / 470 A (75D23L) |
Dtc b2a0f backup battery degradation
TELEMATICS SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2A0F BACKUP BATTERY DEGRADATIONDIAGNOSIS START CONDITION:When ignition switch is ON.DTC DETECTING CONDITION:• Backup battery voltage of charger is low.• Charging attempt of 2 V or more fails ...
Installation
FRONT SUSPENSION > Front Ball JointINSTALLATION1. Install the ball joint assembly to the housing assembly - front axle.CAUTION:• Do not apply grease to the tapered portion of ball stud.• Before tightening, make sure the bottom surface of the housing assembly - front axle and the stepp ...
Gross Axle Weight (GAW) and Gross Axle Weight Rating (GAWR)
Gross Axle Weight
The total weight applied to each axle
(GAW) must never exceed the Gross Axle
Weight Rating (GAWR). The front and rear
GAWs can be adjusted by relocating
passengers and luggage inside the vehicle.
The front and rear GAWR of your
vehicle that is given by SUBARU are also
...