Subaru Crosstrek Service Manual: Dtc b1628 side airbag sensor lh initialization error

Diagnosis start condition:

Ignition voltage is 10 V to 16 V.

DTC detecting condition:

• Open or short circuit in harness of side sensor bus (LH)

• Side airbag sensor (LH) and curtain airbag sensor (LH) are faulty.

• Airbag control module is faulty.

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">

1.CHECK POOR CONTACT OF CONNECTORS.

Check for poor contact of the connectors between the airbag control module and the side airbag sensor (RH).

Is there poor contact?

Replace the airbag rear harness along with body harness.

Diagnostic Chart with Trouble Code > DTC B1628 SIDE AIRBAG SENSOR LH INITIALIZATION ERROR">Go to Step 2.

2.CHECK AIRBAG REAR HARNESS (BETWEEN AIRBAG CONTROL MODULE AND SIDE AIRBAG SENSOR LH).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB21) from seat belt pretensioner (LH).

3) Disconnect the connector (AB31) from curtain airbag module (LH).

4) Disconnect connector (AB19) of the side airbag module (LH).

5) Disconnect the connectors (AB17, AB6, AB18) from airbag control module.

6) Connect the connector (1AG) in the test harness AG to the connectors (AB6, AB17, AB18).

7) Disconnect the connector (AB23) from side airbag sensor (LH), and connect the connector (2V) in test harness V to connector (AB23).

8) Measure the resistance between connector (5AG) in the test harness AG and connector (3V) in the test harness V.

Connector & terminal

(5AG) No. 8 — (3V) No. 2:
(5AG) No. 10 — (3V) No. 1:

Is the resistance less than 10 ??

Diagnostic Chart with Trouble Code > DTC B1628 SIDE AIRBAG SENSOR LH INITIALIZATION ERROR">Go to Step 3.

Replace the airbag rear harness along with body harness.

3.CHECK AIRBAG REAR HARNESS (BETWEEN AIRBAG CONTROL MODULE AND SIDE AIRBAG SENSOR LH).

Measure the resistance between connector (3V) in test harness V and chassis ground, and the resistance between connector (3V) terminals in test harness V.

Connector & terminal

(3V) No. 1 — Chassis ground:

(3V) No. 2 — Chassis ground:

(3V) No. 1 — (3V) No. 2:

Is the resistance 1 M? or more?

Diagnostic Chart with Trouble Code > DTC B1628 SIDE AIRBAG SENSOR LH INITIALIZATION ERROR">Go to Step 4.

Replace the airbag rear harness along with body harness.

4.CHECK AIRBAG CONTROL MODULE.

1) Connect all connectors.

2) Clear the memory. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">

Is DTC B1628 displayed?

Diagnostic Chart with Trouble Code > DTC B1628 SIDE AIRBAG SENSOR LH INITIALIZATION ERROR">Go to Step 5.

Diagnostic Chart with Trouble Code > DTC B1628 SIDE AIRBAG SENSOR LH INITIALIZATION ERROR">Go to Step 6.

5.REPLACE SIDE AIRBAG SENSOR (LH) AND CHECK AIRBAG CONTROL MODULE AFTER REPLACEMENT.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Replace the side airbag sensor (LH). Side Airbag Sensor > REMOVAL">

3) Connect all connectors.

4) Clear the memory. Clear Memory Mode">

5) Perform the Inspection Mode. Inspection Mode">

6) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">

Is the system normal?

Diagnostic Chart with Trouble Code > DTC B1628 SIDE AIRBAG SENSOR LH INITIALIZATION ERROR">Go to Step 6.

Replace the curtain airbag sensor LH. Curtain Airbag Sensor > REMOVAL"> Replace the airbag control module if not operating normally even after replacing the sensor. Airbag Control Module > REMOVAL">

6.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Finish the diagnosis.

Dtc b1627 side airbag sensor lh lost communication

Dtc b1630 curtain airbag sensor rh failure

Other materials:

Connecting a Bluetooth device
To use the Bluetooth audio system, it is necessary to register a Bluetooth device with the system. Registering an additional device 1. Select the "Add" key on the Bluetooth devices connection screen. 2. For more information: Refer to "Registering/ connecting Bluetoothdevice" F5- 65. Se ...

Adjustment
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Inhibitor SwitchADJUSTMENT1. Shift the select lever to “N” range.2. Loosen the two bolts holding the inhibitor switch.3. Insert the ST vertically into the holes of the shifter arm and switch body.ST 499267300STOPPER PIN4. Tighten the two ...

Outside mirrors
Convex mirror (passenger side) WARNING In the Subaru Ascent, the passenger-side outside mirror uses a convex design, which alters depth perception. Objects reflected in this mirror appear smaller and farther away than they actually are. For this reason, never rely solely on the convex mirror ...