Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: General diagnostic table Inspection

Subaru Crosstrek Service Manual / Engine (diagnostics)(h4do) / General diagnostic table Inspection

ENGINE (DIAGNOSTICS)(H4DO) > General Diagnostic Table

INSPECTION

1. ENGINE

NOTE:

Malfunction of parts other than those listed is also possible. Engine Trouble in General">

Symptoms

Faulty parts

1. Engine stalls during idling.

1) Manifold absolute pressure sensor

2) Mass air flow and intake air temperature sensor

3) Ignition parts (*1)

4) Engine coolant temperature sensor (*2)

5) Crankshaft position sensor (*3)

6) Camshaft position sensor (*3)

7) Fuel injection parts (*4)

8) Electronic throttle control

2. Rough idling

1) Manifold absolute pressure sensor

2) Mass air flow and intake air temperature sensor

3) Engine coolant temperature sensor (*2)

4) Ignition parts (*1)

5) Air intake system (*5)

6) Fuel injection parts (*4)

7) Electronic throttle control

8) Crankshaft position sensor (*3)

9) Camshaft position sensor (*3)

10) Oxygen sensor

11) Fuel pump and fuel pump relay

12) EGR control valve

3. Engine does not return to idle.

1) Engine coolant temperature sensor

2) Electronic throttle control

3) Manifold absolute pressure sensor

4) Mass air flow and intake air temperature sensor

5) EGR control valve

6) Accelerator pedal position sensor

7) Engine oil temperature sensor

4. Poor acceleration

1) Manifold absolute pressure sensor

2) Mass air flow and intake air temperature sensor

3) Electronic throttle control

4) Fuel injection parts (*4)

5) Fuel pump and fuel pump relay

6) Engine coolant temperature sensor (*2)

7) Crankshaft position sensor (*3)

8) Camshaft position sensor (*3)

9) Engine torque control signal circuit

10) Ignition parts (*1)

11) EGR control valve

12) Accelerator pedal position sensor

13) Engine oil temperature sensor

5. Engine stalls, hesitates, or sputters at acceleration.

1) Manifold absolute pressure sensor

2) Mass air flow and intake air temperature sensor

3) Engine coolant temperature sensor (*2)

4) Crankshaft position sensor (*3)

5) Camshaft position sensor (*3)

6) Purge control solenoid valve

7) Fuel injection parts (*4)

8) Electronic throttle control

9) Fuel pump and fuel pump relay

10) EGR control valve

6. Surging

1) Mass air flow and intake air temperature sensor

2) Manifold absolute pressure sensor

3) Engine coolant temperature sensor (*2)

4) Crankshaft position sensor (*3)

5) Camshaft position sensor (*3)

6) Fuel injection parts (*4)

7) Electronic throttle control

8) Fuel pump and fuel pump relay

9) EGR control valve

7. Spark knock

1) Mass air flow and intake air temperature sensor

2) Manifold absolute pressure sensor

3) Engine coolant temperature sensor

4) Knock sensor

5) Fuel injection parts (*4)

6) Fuel pump and fuel pump relay

7) EGR control valve

8. After burning in exhaust system

1) Mass air flow and intake air temperature sensor

2) Manifold absolute pressure sensor

3) Engine coolant temperature sensor (*2)

4) Fuel injection parts (*4)

5) Fuel pump and fuel pump relay

*1: Check ignition coil and spark plug.

*2: Indicate the symptom occurring only in cold temperatures.

*3: Ensure the secure installation.

*4: Check fuel injector and fuel filter.

*5: Inspect air leak in air intake system.

Engine control module (ecm) i/o signal Electrical specification
ENGINE (DIAGNOSTICS)(H4DO) > Engine Control Module (ECM) I/O SignalELECTRICAL SPECIFICATION1. ENGINE CONTROL MODULE (ECM)DescriptionConnector No.Terminal No.Signal (V)NoteIgnition SW ON(Engine OFF) ...

General scan tool Operation
ENGINE (DIAGNOSTICS)(H4DO) > General Scan ToolOPERATION1. HOW TO USE GENERAL SCAN TOOL1. Prepare a scan tool (general scan tool) required by SAE J1978.2. Connect the general scan tool to data link ...

Other materials:

Removal
LIGHTING SYSTEM > Side Turn Signal Light AssemblyREMOVAL1. Disconnect the ground cable from battery. NOTE">2. Remove the light assembly - side turn mirror. Outer Mirror Assembly > DISASSEMBLY"> ...

Tire pressures and wear
Maintaining the correct tire pressures helps to maximize the tires' service lives and is essential for good running performance. Check and, if necessary, adjust the pressure of each tire (including the spare - if equipped) at least once a month (for example, during a fuel stop) and before a ...

Inspection
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Reverse Brake AssemblyINSPECTION• Inspect the drive plate facing for wear and damage.• Check the driven plate for discoloration (burnt color).• Check for worn snap ring, fatigue or damaged return spring or deformed spring retainer.&bul ...

© 2016-2026 Copyright www.sucross.com