Subaru Crosstrek Service Manual: Dtc b1831 open in curtain airbag rh squib circuit

Diagnosis start condition:

Ignition voltage is 10 V to 16 V.

DTC detecting condition:

• Curtain airbag harness (RH) circuit is open.

• Curtain airbag module (RH) is faulty.

• Airbag control module is faulty.

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">

1.CHECK POOR CONTACT OF CONNECTORS.

Check for poor contact of the connectors between the airbag control module, curtain airbag module RH and the curtain airbag sensor RH.

Is there poor contact?

Replace the airbag rear harness along with body harness.

Diagnostic Chart with Trouble Code > DTC B1831 OPEN IN CURTAIN AIRBAG RH SQUIB CIRCUIT">Go to Step 2.

2.CHECK CURTAIN AIRBAG MODULE.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB33) from curtain airbag module (RH).

3) Connect the connector (1N) in the test harness N to the connector (AB33).

4) Connect the airbag resistor to the connector (2N) of test harness N.

5) Connect the battery ground terminal and turn the ignition switch to ON.

Does the airbag warning light illuminate for 6 seconds and go off?

Replace the curtain airbag module (RH). Curtain Airbag Module">

Diagnostic Chart with Trouble Code > DTC B1831 OPEN IN CURTAIN AIRBAG RH SQUIB CIRCUIT">Go to Step 3.

3.CHECK AIRBAG REAR HARNESS (CURTAIN AIRBAG MODULE HARNESS RH).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB26) from seat belt pretensioner (RH).

3) Disconnect connector (AB24) from side airbag module (RH).

4) Disconnect the airbag resistor from test harness N.

5) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.

6) Connect the connector (1AG) in the test harness AG to the connectors (AB6, AB17, AB18).

7) Measure the resistance between connector (6AG) in the test harness AG and connector (2N) in the test harness N.

Connector & terminal

(6AG) No. 8 — (2N) No. 2:
(6AG) No. 6 — (2N) No. 1:

Is the resistance less than 10 ??

Diagnostic Chart with Trouble Code > DTC B1831 OPEN IN CURTAIN AIRBAG RH SQUIB CIRCUIT">Go to Step 4.

Replace the airbag rear harness along with body harness.

4.CHECK AIRBAG CONTROL MODULE.

1) Connect all connectors.

2) Clear the memory. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">

Is DTC B1831 displayed?

Replace the airbag control module. Airbag Control Module">

Diagnostic Chart with Trouble Code > DTC B1831 OPEN IN CURTAIN AIRBAG RH SQUIB CIRCUIT">Go to Step 5.

5.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Finish the diagnosis.

Dtc b1830 short in curtain airbag rh squib circuit

Dtc b1832 short in curtain airbag rh squib circuit (to ground)

Other materials:

Installation
DRIVE SHAFT SYSTEM > Rear AxleINSTALLATION1. Temporarily tighten the rear axle housing to the upper arm assembly.2. Install the rear drive shaft assembly.CAUTION:• Do not hammer the drive shaft assembly when installing.• Use new axle nuts.(1) Insert the drive shaft assembly into the h ...

To arm the system using power door locking switches
1. Close all windows. 2. Remove the key from the ignition switch (models without "keyless access with push-button start system")/turn the push-button ignition switch to the "OFF" position (models with "keyless access with push-button start system"). 3. Open the doors and get out of the v ...

Dtc b1015 key interlock circuit
BODY CONTROL SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B1015 KEY INTERLOCK CIRCUITDTC detecting condition:Ground short of key interlock circuitTrouble symptom:Key interlock does not keep lock condition.Wiring diagram:Shift lock control system Shift Lock Co ...