Subaru Crosstrek Service Manual: Dtc b1830 short in curtain airbag rh squib circuit

Diagnosis start condition:

Ignition voltage is 10 V to 16 V.

DTC detecting condition:

• Curtain airbag harness (RH) circuit is shorted.

• Curtain airbag module (RH) is faulty.

• Airbag control module is faulty.

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">

1.CHECK POOR CONTACT OF CONNECTORS.

Check for poor contact of the connectors between the airbag control module, curtain airbag module RH and the curtain airbag sensor RH.

Is there poor contact?

Replace the airbag rear harness along with body harness.

Diagnostic Chart with Trouble Code > DTC B1830 SHORT IN CURTAIN AIRBAG RH SQUIB CIRCUIT">Go to Step 2.

2.CHECK CURTAIN AIRBAG MODULE.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB33) from curtain airbag module (RH).

3) Connect the connector (1N) in the test harness N to the connector (AB33).

4) Connect the airbag resistor to the connector (2N) of test harness N.

5) Connect the battery ground terminal and turn the ignition switch to ON.

Does the airbag warning light illuminate for 6 seconds and go off?

Replace the curtain airbag module (RH). Curtain Airbag Module">

Diagnostic Chart with Trouble Code > DTC B1830 SHORT IN CURTAIN AIRBAG RH SQUIB CIRCUIT">Go to Step 3.

3.CHECK AIRBAG REAR HARNESS (CURTAIN AIRBAG MODULE HARNESS RH).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB26) from seat belt pretensioner (RH).

3) Disconnect connector (AB24) from side airbag module (RH).

4) Disconnect the airbag resistor from test harness N.

5) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.

6) Connect the connector (1AG) in the test harness AG to the connectors (AB6, AB17, AB18).

7) Measure the resistance between connector (6AG) terminals in test harness AG.

Connector & terminal

(6AG) No. 6 — (6AG) No. 8:

Is the resistance 1 M? or more?

Diagnostic Chart with Trouble Code > DTC B1830 SHORT IN CURTAIN AIRBAG RH SQUIB CIRCUIT">Go to Step 4.

Replace the airbag rear harness along with body harness.

4.CHECK AIRBAG CONTROL MODULE.

1) Connect all connectors.

2) Clear the memory. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">

Is DTC B1830 displayed?

Replace the airbag control module. Airbag Control Module">

Diagnostic Chart with Trouble Code > DTC B1830 SHORT IN CURTAIN AIRBAG RH SQUIB CIRCUIT">Go to Step 5.

5.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Finish the diagnosis.

Dtc b1828 short in side airbag lh (to +b)

Dtc b1831 open in curtain airbag rh squib circuit

Other materials:

Inspection
ENTERTAINMENT > Switches and HarnessINSPECTION1. SATELLITE SWITCH ASSEMBLY1. Measure the resistance between connector terminals.Preparation tool:Circuit testerTerminal No.Inspection conditionsStandard6 — 2VOL (+)VOL (−)SEEK (›)SEEK (‹)LISTRETURNA circuit is all OFF.Approx. 1 ...

Screen Settings
After entering the "Screen Settings" menu, select one of the following menus. Welcome Good-bye Screen The welcome screen/good-bye screens can be activated or deactivated. Select "On" to activate the screens. Select "Off" to deactivate the screens. Gauge Initial Movement The movement of the m ...

Dtc u0423 invalid data received from instrument panel cluster control module
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0423 INVALID DATA RECEIVED FROM INSTRUMENT PANEL CLUSTER CONTROL MODULEReceived error data from combination meter.NOTE:Perform the diagnosis for LAN system. Basic Diagnostic ...