Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Component

COOLING(H4DO) > General Description

COMPONENT

1. WATER PUMP

(1)

Water pump pulley

(13)

Clip

(25)

Gasket

(2)

Water pump ASSY

(14)

Water pipe hose RH

(26)

Engine coolant temperature sensor

(3)

Gasket

(15)

Water pipe ASSY (CVT model)

(27)

EGR control valve

(4)

Thermostat (engine side)

(16)

Preheater hose A

(28)

O-ring

(5)

Gasket (engine side)

(17)

Clip

(29)

Gasket

(6)

Thermostat cover (engine side)

(18)

Preheater hose B

(30)

Water pipe ASSY (MT model)

(7)

Clip

(19)

Clip

(8)

Water pipe hose LH

(20)

O-ring

Tightening torque: N·m (kgf-m, ft-lb)

(9)

Water pipe LH

(21)

Thermostat (CVTF cooler (with warmer feature) side)

T1:

6.4 (0.7, 4.7)

(10)

Preheater hose

(22)

Gasket (CVTF cooler (with warmer feature) side)

T2:

14 (1.4, 10.3)

(11)

Clip

(23)

Gasket (MT model)

T3:

18 (1.8, 13.3)

(12)

Water pipe RH

(24)

Thermostat cover (CVTF cooler (with warmer feature) side)

T4:

22 (2.2, 16.2)

2. RADIATOR & RADIATOR FAN

(1)

Radiator lower cushion

(11)

Radiator sub fan

(20)

Radiator upper gasket

(2)

Radiator

(12)

Radiator main fan shroud

(21)

Radiator lower gasket

(3)

Radiator upper cushion

(13)

Radiator main fan

(4)

Radiator upper bracket

(14)

Radiator outlet hose

Tightening torque: N·m (kgf-m, ft-lb)

(5)

Clip

(15)

Radiator drain plug

T1:

3.4 (0.3, 2.5)

(6)

Radiator inlet hose

(16)

O-ring

T2:

4.41 (0.45, 3.25)

(7)

Engine coolant reservoir tank cap

(17)

Radiator cap

T3:

7.5 (0.8, 5.5)

(8)

Over flow hose

(18)

Sub fan motor

T4:

12 (1.2, 8.9)

(9)

Engine coolant reservoir tank

(19)

Main fan motor

(10)

Radiator sub fan shroud

Specification
COOLING(H4DO) > General DescriptionSPECIFICATIONCooling systemElectric fan + forced engine coolant circulation systemTotal engine coolant capacityL (US qt, Imp qt)CVT modelApprox. 8.4 (8.9, 7.4)MT ...

Preparation tool
COOLING(H4DO) > General DescriptionPREPARATION TOOL1. SPECIAL TOOLILLUSTRATIONTOOL NUMBERDESCRIPTIONREMARKS18355AA000PULLEY WRENCH• Used for removing and installing water pump pulley.• ...

Other materials:

Installation
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > FRESH/RECIRC Door ActuatorINSTALLATIONCAUTION:• After installing the grille assembly - ventilation RH, check that the air vent grille of the grille assembly - ventilation RH is inserted correctly into the air vent duct.• Before handling the a ...

Removal
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Air Breather HoseREMOVAL1. Disconnect the ground cable from battery.2. Remove the clip (A) from the air intake boot.3. Loosen the clamp (B) connecting the air intake boot and air cleaner case (rear).4. Loosen the clamp (C) which connects the air intake ...

Removal
DIFFERENTIALS > Rear Differential Front MemberREMOVAL1. Disconnect the ground cable from battery.2. Lift up the vehicle.3. Support the rear differential using transmission jack, and then remove the rear differential front member.(A)Rear differential front member ...

© 2016-2026 Copyright www.sucross.com