Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Basic diagnostic procedure Procedure

Subaru Crosstrek Service Manual / Body control system (diagnostics) / Basic diagnostic procedure Procedure

BODY CONTROL SYSTEM (DIAGNOSTICS) > Basic Diagnostic Procedure

PROCEDURE

CAUTION:

Subaru Select Monitor is required for reading DTC, performing diagnosis and reading current data.

Remove foreign matter (dust, water, oil, etc.) from the body integrated unit connector during removal and installation.

Registration of immobilizer may be needed after the replacement of control modules, etc. For detailed procedure, refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume.

NOTE:

To check harness for open or short circuits, shake the suspected trouble spot or connector.

Check List for Interview Check List for Interview">

STEPCHECKYESNO

1.CHECK PRE-INSPECTION.

Ask the customer when and how the trouble occurred using the interview check list. Check List for Interview">

Did you interview the customer?

Basic Diagnostic Procedure > PROCEDURE">Go to Step 2.

Interview the customer.

2.BASIC INSPECTION.

Check components which might affect body control. General Description > INSPECTION">

Is the component that might influence the body control problem normal?

Basic Diagnostic Procedure > PROCEDURE">Go to Step 3.

Repair or replace each component.

3.CHECK DTC.

1) Read the DTC. Read Diagnostic Trouble Code (DTC)">

NOTE:

If the communication function of the Subaru Select Monitor cannot be executed properly, check the communication circuit. Subaru Select Monitor > COMMUNICATION FOR INITIALIZING IMPOSSIBLE">

2) Record all DTCs, time stamp and freeze frame data.

NOTE:

For time stamp, refer to “LAN SYSTEM”. General Description > CAUTION">

Is DTC displayed on Subaru Select Monitor?

Basic Diagnostic Procedure > PROCEDURE">Go to Step 5.

Basic Diagnostic Procedure > PROCEDURE">Go to Step 4.

4.PERFORM GENERAL DIAGNOSTICS.

Inspect using the “General Diagnostic Table”. General Diagnostic Table">

Is result of inspection OK?

The body control system is normal.

Basic Diagnostic Procedure > PROCEDURE">Go to Step 5.

5.PERFORM DIAGNOSIS.

1) Correct the cause of trouble.

2) Perform the Clear Memory Mode. Clear Memory Mode">

3) Read the DTC. Read Diagnostic Trouble Code (DTC)">

Is DTC displayed on Subaru Select Monitor?

Repeat step 5 until DTC is not shown.

Finish the diagnosis.

List
BODY CONTROL SYSTEM (DIAGNOSTICS) > Read Current DataLISTItems to be displayedUnit of measureContentNoteBATT voltage (control)10 — 15 VBody integrated unit input valueAlwaysBATT voltage (BACKUP)1 ...

Check list for interview Check
BODY CONTROL SYSTEM (DIAGNOSTICS) > Check List for InterviewCHECKInspect the following items regarding the vehicle’s state.Body Control System Check List for Interview ...

Other materials:

Dtc b1630 curtain airbag sensor rh failure
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B1630 CURTAIN AIRBAG SENSOR RH FAILUREDIAGNOSIS START CONDITION:Ignition voltage is 10 V to 16 V.DTC DETECTING CONDITION:Curtain airbag sensor (RH) is faulty.If DTC B1630 is displayed, the circuit within the curtain airbag sensor ...

Headlights (models without HID headlights)
CAUTION Halogen headlight bulbs become very hot while in use. If you touch the bulb surface with bare hands or greasy gloves, fingerprints or grease on the bulb surface will develop into hot spots, causing the bulb to break. If there are finger prints or grease on the bulb surface, wipe the ...

Inspection
BRAKE > Brake BoosterINSPECTION1. OPERATION CHECK WHEN NOT USING MEASURING DEVICESCAUTION:When checking operation, be sure to apply the parking brake securely.When an operation check is performed with no measuring devices, a faulty part cannot be identified correctly. But it is possible to identi ...

© 2016-2023 Copyright www.sucross.com