Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Preparation tool

DRIVE SHAFT SYSTEM > General Description

PREPARATION TOOL

1. SPECIAL TOOL

ILLUSTRATION

PART NO.

DESCRIPTION

REMARKS

20099PA010

INSTALLER & REMOVER

Used for replacing the rear bushing of rear axle housing.

Used together with BUSHING REMOVER (20099FG000).

20099FG000

BUSHING REMOVER

Used for replacing the rear bushing of rear axle housing.

Used together with base part of INSTALLER & REMOVER (20099PA010).

28099AC000

BOOT BAND PLIERS

Used for tightening the boot band.

(For front drive shaft)

925091000

BAND TIGHTENING TOOL

Used for tightening the boot band.

(A) Jig for the band

(B) Ratchet wrench

18675AA000

DIFFERENTIAL SIDE OIL SEAL INSTALLER

Used for installing the differential side retainer oil seal.

926470000

AXLE SHAFT PULLER

Used for removing the drive shaft.

Used together with AXLE SHAFT PULLER PLATE (28099PA110).

28099PA110

AXLE SHAFT PULLER PLATE

Exchange with the plate of the AXLE SHAFT PULLER (926470000) to use.

927080000

HUB STAND

Used for assembling hub bolt in hub.

28399AG000

HUB STAND

Used for extracting hub bolt.

28399SA010

OIL SEAL PROTECTOR

Used for installing front drive shaft into front differential.

For protecting the oil seal.

28099PA090

OIL SEAL PROTECTOR

Used for installing the rear drive shaft to the rear differential.

For protecting the oil seal.

28099PA100

DRIVE SHAFT REMOVER

Used for removing the rear drive shaft from rear differential. (T-type)

2. GENERAL TOOL

TOOL NAME

REMARKS

Tie-rod ball joint puller

Used for disconnecting joints.

Dial gauge

Used for inspecting the propeller shaft run-out.

Extension cap

Used for preventing leakage of gear oil or CVTF.

Crowbar

Used for extracting drive shaft.

Needle nose pliers

Used for tightening the boot band of the rear drive shaft.

Snap-on 96BCP

Or equivalent.

Component
DRIVE SHAFT SYSTEM > General DescriptionCOMPONENT1. PROPELLER SHAFT(1)Propeller shaft(3)Rear differential (T-type)Tightening torque: N·m (kgf-m, ft-lb)(2)Rear differential (VA1-type) T1:31 ...

Propeller shaft
...

Other materials:

Specification
CLUTCH SYSTEM > General DescriptionSPECIFICATIONModel2.0 LTransmission type5MTClutch coverTypePush typeDiaphragm set loadN (kgf, lbf)5,688 (580, 1,279)Clutch discFacing materialWoven (non-asbestos)O.D. ? I.D. ? Thicknessmm (in)Flywheel side225 ? 150 ? 3.2 (8.86 ? 5.9 ? 0.126)Clutch cover side225 ...

A/c filter Replacement
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > A/C FilterREPLACEMENT1. Remove the pocket assembly.(1) Attach the protective tape (a) to the panel center LWR.(2) Remove the damper COMPL - pocket.(3) Release the stoppers and remove the pocket assembly by pulling it toward you.2. Pinch the tabs to relea ...

Installation
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Fuel Filler PipeINSTALLATION1. Open the fuel filler lid.2. Insert the fuel filler pipe assembly into the rubber saucer from inside of the rear fender.3. Install the fuel filler pipe assembly to the vehicle.Tightening torque:7.5 N·m (0.8 kgf-m, 5.5 ft-l ...

© 2016-2023 Copyright www.sucross.com