Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: List of diagnostic trouble code (dtc) List

Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > List of Diagnostic Trouble Code (DTC)

LIST

DTC

Item

Reference

B2300

REAR RADAR CIRCUIT LOW

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2300 REAR RADAR CIRCUIT LOW">

B2301

REAR RADAR CIRCUIT HIGH

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2301 REAR RADAR CIRCUIT HIGH">

B2304

REAR RADAR ON-OFF SWITCH STUCK

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2304 REAR RADAR ON-OFF SWITCH STUCK">

NOTE:

Only radar sensor LH (master) is detected.

B2311

REAR RADAR DETECT TCM

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2311 REAR RADAR DETECT TCM">

B2313

REAR RADAR DETECT VDC

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2313 REAR RADAR DETECT VDC">

B2327

REAR RADAR INTERNAL FAILURE (INTERNAL ELECTRIC CIRCUIT)

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2327 REAR RADAR INTERNAL FAILURE (INTERNAL ELECTRIC CIRCUIT)">

B2329

REAR RADAR AXIS ALIGNMENT INCOMPLETE

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2329 REAR RADAR AXIS ALIGNMENT INCOMPLETE">

B2350

REAR RADAR COMMUNICATION ERROR BETWEEN MASTER AND SLAVE

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2350 REAR RADAR COMMUNICATION ERROR BETWEEN MASTER AND SLAVE">

U0073

CONTROL MODULE COMMUNICATION BUS OFF

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0073 CONTROL MODULE COMMUNICATION BUS OFF">

U0101

LOST COMMUNICATION WITH TCM

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">

U0122

LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULE

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0122 LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULE">

U0140

LOST COMMUNICATION WITH BODY CONTROL MODULE

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0140 LOST COMMUNICATION WITH BODY CONTROL MODULE">

U0155

LOST COMMUNICATION WITH INSTRUMENT PANEL CLUSTER (IPC) CONTROL MODULE

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0155 LOST COMMUNICATION WITH INSTRUMENT PANEL CLUSTER (IPC) CONTROL MODULE">

U0402

INVALID DATA RECEIVED FROM TCM

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0402 INVALID DATA RECEIVED FROM TCM">

U0416

INVALID DATA RECEIVED FROM VEHICLE DYNAMICS CONTROL MODULE

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0416 INVALID DATA RECEIVED FROM VEHICLE DYNAMICS CONTROL MODULE">

U0422

INVALID DATA RECEIVED FROM BODY CONTROL MODULE

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0422 INVALID DATA RECEIVED FROM BODY CONTROL MODULE">

U0423

INVALID DATA RECEIVED FROM INSTRUMENT PANEL CLUSTER CONTROL MODULE

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0423 INVALID DATA RECEIVED FROM INSTRUMENT PANEL CLUSTER CONTROL MODULE">

List of cancel code List
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > List of Cancel CodeLISTCodeItemContents of diagnosisB2320Rear RADAR Low Voltage (less than 9V)Temporarily stops because the voltage sup ...

Read cancel code Operation
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Read Cancel CodeOPERATION1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle in ...

Other materials:

ECO gauge (if equipped)
U.S.-spec. models Except U.S.-spec. models The ECO gauge shows the difference between the current rate of fuel consumption and the average rate of fuel consumption since the trip meter was last reset. If the needle of the gauge moves towards the right side, this indicates better f ...

Dtc b2275 engine start request control circuit
KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2275 ENGINE START REQUEST CONTROL CIRCUITDTC detecting condition:• When malfunction is detected in engine start permission signal output circuit in the keyless access CM. ...

Inspection
CONTROL SYSTEMS > AT Shift Lock Control SystemINSPECTION1. SHIFT LOCK OPERATION• Model without push button ignition switchSTEPCHECKYESNO1.CHECK COMMUNICATION OF SUBARU SELECT MONITOR.1) Turn the ignition switch to ON.2) Using the Subaru Select Monitor, check whether communication to all sys ...

© 2016-2023 Copyright www.sucross.com