Subaru Crosstrek Service Manual: Installation
FRONT SUSPENSION > Front Strut
INSTALLATION
1. Install the strut mount - front at the upper side of the strut to the body, and tighten it with new flange nuts.
Tightening torque:
20 N·m (2.04 kgf-m, 14.8 ft-lb)
2. Align alignment marks on the camber adjusting bolt and strut.
Using new self-locking nuts, install the strut to the housing assembly - front axle.
NOTE:
While holding the head of adjusting bolt, tighten the nut.
Tightening torque:
155 N·m (15.81 kgf-m, 114.3 ft-lb)
3. Secure the ABS wheel speed sensor harness bracket to the strut.
CAUTION:
During the installation, make sure that the marking of ABS wheel speed sensor harness does not twist.
4. Install the brake hose bracket.
Tightening torque:
33 N·m (3.36 kgf-m, 24.3 ft-lb)
5. Install the front wheels.
Tightening torque:
Except for C4 model: 120 N·m (12.24 kgf-m, 88.5 ft-lb)
C4 model: 100 N·m (10.20 kgf-m, 73.8 ft-lb)
6. Inspect the wheel alignment and adjust if necessary.
• Inspection: Wheel Alignment > INSPECTION">
• Adjustment: Wheel Alignment > ADJUSTMENT">
CAUTION:
When the wheel alignment has been adjusted, perform the following VDC setting mode.
– Model without EyeSight: VDC sensor midpoint setting mode VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > ADJUSTMENT">
– Model with EyeSight: Neutral of Steering Angle Sensor & Lateral G Sensor 0 point setting VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > ADJUSTMENT">
– Model with EyeSight: Longitudinal G sensor & lateral G sensor 0 point setting VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > ADJUSTMENT">
7. Perform reinitialization of the auto headlight beam leveler system. (Model with auto headlight beam leveler) Auto Headlight Beam Leveler System > PROCEDURE">
Inspection
FRONT SUSPENSION > Front StrutINSPECTIONCheck the removed part for wear, damage and cracks, and then repair or replace it if defective.1. STRUT1. Check for oil leaks.2. Move the piston rod up and d ...
Other materials:
Dtc u0126 lost communication with steering angle sensor module
LAN SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0126 LOST COMMUNICATION WITH STEERING ANGLE SENSOR MODULEDTC DETECTING CONDITION:No data is received from steering angle sensor.TROUBLE SYMPTOM:VDC CM does not operate normally.STEPCHECKYESNO1.CHECK PERFORMING ...
Dtc b1831 open in curtain airbag rh squib circuit
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B1831 OPEN IN CURTAIN AIRBAG RH SQUIB CIRCUITDiagnosis start condition:Ignition voltage is 10 V to 16 V.DTC detecting condition:• Curtain airbag harness (RH) circuit is open.• Curtain airbag module (RH) is faulty.&bul ...
Assembly
COOLING(H4DO) > Radiator Main Fan and Fan MotorASSEMBLYAssemble in the reverse order of disassembly.Tightening torque:4.41 N·m (0.45 kgf-m, 3.25 ft-lb)Tightening torque:3.4 N·m (0.3 kgf-m, 2.5 ft-lb) ...
