Subaru Crosstrek Service Manual: Dtc u0327 software incompatibility with vehicle security control module

DTC DETECTING CONDITION:

No data is received from keyless access CM.

TROUBLE SYMPTOM:

Cooperation control of keyless access does not operate properly.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0327 SOFTWARE INCOMPATIBILITY WITH VEHICLE SECURITY CONTROL MODULE">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0327 SOFTWARE INCOMPATIBILITY WITH VEHICLE SECURITY CONTROL MODULE">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is U0327 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0327 SOFTWARE INCOMPATIBILITY WITH VEHICLE SECURITY CONTROL MODULE">Go to Step 4.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0327 SOFTWARE INCOMPATIBILITY WITH VEHICLE SECURITY CONTROL MODULE">Go to Step 8.

4.CHECK DTC.

1) Check CAN communication circuit. CAN Communication Circuit Check">

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0327 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0327 SOFTWARE INCOMPATIBILITY WITH VEHICLE SECURITY CONTROL MODULE">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0327 SOFTWARE INCOMPATIBILITY WITH VEHICLE SECURITY CONTROL MODULE">Go to Step 8.

5.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the smart data no-receive detected in several modules?

Replace the keyless access CM. Keyless Access CM">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0327 SOFTWARE INCOMPATIBILITY WITH VEHICLE SECURITY CONTROL MODULE">Go to Step 6.

6.REPLACE MODULE.

1) Replace the keyless access CM.

NOTE:

Do not register the keyless access CM.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0327 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0327 SOFTWARE INCOMPATIBILITY WITH VEHICLE SECURITY CONTROL MODULE">Go to Step 7.

System is normal.

NOTE:

Be sure to perform keyless access CM registration.

7.CHECK MODULE.

1) Reinstall the keyless access CM.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0327 a current malfunction?

Replace the keyless access CM. Keyless Access CM">

System is normal.

8.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0327 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0327 SOFTWARE INCOMPATIBILITY WITH VEHICLE SECURITY CONTROL MODULE">Go to Step 9.

9.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Dtc u0164 lost communication with hvac control module

Dtc u0401 invalid data received from ecm/pcm a

Other materials:

Dtc p0976 shift solenoid "b" control circuit low
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0976 SHIFT SOLENOID "B" CONTROL CIRCUIT LOWDTC detecting condition:Immediately at fault recognitionTrouble symptom:Gear is not changed. (No down-shift)CAUTION:Use the check boa ...

Assembly
BRAKE > Rear Disc Brake AssemblyASSEMBLY1. Before installation, check each part. Rear Disc Brake Assembly > INSPECTION">2. Clean the inside of the caliper body cylinder using brake fluid.3. Apply a coat of brake fluid to piston seal and install the piston seal to the caliper body cyli ...

Dtc u0131 lost communication with power steering control module
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0131 LOST COMMUNICATION WITH POWER STEERING CONTROL MODULEDetected when CAN data is not received from electric power steering CM.NOTE:Perform the diagnosis for LAN system. Basic Diagnostic Pro ...