Subaru Crosstrek Service Manual: Dtc u0164 lost communication with hvac control module

DTC DETECTING CONDITION:

No data is received from A/C control panel.

TROUBLE SYMPTOM:

Cooperation control of air conditioner does not operate properly.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is U0164 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 4.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 8.

4.CHECK DTC.

1) Check CAN communication circuit. CAN Communication Circuit Check">

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0164 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 8.

5.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the air conditioner data no-receive detected in several modules?

Replace the A/C control panel. Control Panel">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 6.

6.REPLACE MODULE.

1) Replace the A/C control panel.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0164 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 7.

System is normal.

7.CHECK MODULE.

1) Restore the A/C control panel.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0164 a current malfunction?

Replace the A/C control panel. Control Panel">

System is normal.

8.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0164 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 9.

9.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Dtc u0155 lost communication with instrument panel cluster (ipc) control module

Dtc u0327 software incompatibility with vehicle security control module

Other materials:

Dtc b1903 short in front p/t rh (to +b)
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B1903 SHORT IN FRONT P/T RH (TO +B)Diagnosis start condition:Ignition voltage is 10 V to 16 V.DTC detecting condition:• Seat belt pretensioner (RH) circuit is shorted to power supply.• Pretensioner (RH) is faulty.&bul ...

Open/close
To open: First unlock the rear gate lock then push the rear gate opener button. To close: Lower the rear gate slowly and push down firmly until the latch engages. The rear gate can be lowered easily if you pull it down holding the recessed grip. WARNING To prevent dangerous exhaust ...

Removal
EXTERIOR/INTERIOR TRIM > Rear BumperREMOVAL1. CROSSTREK MODEL1. Disconnect the ground cable from battery. NOTE">2. Remove the light assembly - rear combination.CAUTION:Be careful not to damage the clips.(1) Release the bolts and clips, then pull out the light assembly - rear combination ...