Subaru Crosstrek Service Manual: Specification
LUBRICATION(H4DO) > General Description
SPECIFICATION
Lubrication method | Forced lubrication | ||||
Oil pump | Pump type | Trochoid type | |||
Number of teeth | Inner rotor | 11 | |||
Outer rotor | 12 | ||||
Outer rotor diameter ? Thickness | mm (in) | 77 ? 12 (3.03 ? 0.47) | |||
Performance (Oil temperature 120°C (248°F)) | 600 r/min | Discharge pressure | kPa (kg/cm2, psi) | 40 (0.4, 5.8) | |
Discharge rate | L (US qt, Imp qt)/min | 5.8 (6.1, 5.1) or more | |||
6,000 r/min | Discharge pressure | kPa (kg/cm2, psi) | 323 (3.3, 46.8) | ||
Discharge rate | L (US qt, Imp qt)/min | 55 (58.1, 48.4) or more | |||
Relief valve working pressure (2-step relief) | 1st opening pressure | kPa (kg/cm2, psi) | 150 (1.5, 21.7) | ||
Main opening pressure | kPa (kg/cm2, psi) | 570 (5.8, 82.6) | |||
Oil filter | Filter type | Full-flow filter type | |||
Filtration area | cm2 (sq in) | Outer diameter: 68 mm (2.68 in) (black) | 1,100 (171) | ||
Outer diameter: 67.4 mm (2.65 in) (blue) | 867 (134.3) | ||||
By-pass valve opening pressure | kPa (kg/cm2, psi) | 160 (1.6, 23.2) | |||
Outer diameter ? Width | mm (in) | Outer diameter: 68 mm (2.68 in) (black) | 68 ? 85 (2.68 ? 3.35) | ||
Outer diameter: 67.4 mm (2.65 in) (blue) | 67.4 ? 87.1 (2.65 ? 3.43) | ||||
Installation screw specifications | M 20 ? 1.5 | ||||
Oil pressure switch | Type | Immersed contact point type | |||
Operating voltage | 12 V | ||||
Warning light operating pressure | kPa (kg/cm2, psi) | 14.7 (0.1, 2.1) | |||
Proof pressure | kPa (kg/cm2, psi) | 981 (10, 142.2) | |||
Engine oil | Total capacity (at overhaul) | L (US qt, Imp qt) | 5.7 (6.0, 5.0) | ||
When replacing engine oil and oil filter | L (US qt, Imp qt) | 4.8 (5.1, 4.2) | |||
When replacing engine oil only | L (US qt, Imp qt) | 4.6 (4.9, 4.0) | |||
Specified oil:
CAUTION:
• Use 0W-20 (synthetic oil).
• It is acceptable to fill an engine with oil of another brand when replacing the oil, but make sure to use the following engine oil specified by Subaru.
NOTE:
The proper viscosity oil helps the engine maintain its ideal temperature, and cranking speed increased by reducing viscosity friction in hot condition.
Engine oil standard | SAE viscosity No. | ||
Those with SN “Resource Conserving” logo in case of API standard.
or
Those with GF-5 “starburst mark” displayed on top of the container in case of ILSAC standard.
0W-20 (synthetic oil)
Caution
LUBRICATION(H4DO) > General DescriptionCAUTION• Prior to starting work, pay special attention to the following:1. Always wear work clothes, a work cap, and protective shoes. Additionally, wea ...
Component
LUBRICATION(H4DO) > General DescriptionCOMPONENT1. OIL PAN AND STRAINER(1)Oil pan upper(8)Drain plug gasketTightening torque: N·m (kgf-m, ft-lb)(2)O-ring(9)Drain plugT1:5 (0.5, 3.7)(3)Baffle ...
Other materials:
Diagnostic procedure for subaru select monitor communication Communication for initializing impossible
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure for Subaru Select Monitor CommunicationCOMMUNICATION FOR INITIALIZING IMPOSSIBLEDiagnosis:Defective harness connectorTrouble symptom:Subaru Select Monitor communication failureCAUTION:Use the check board when measuring the TC ...
Replacement
DIFFERENTIALS > Rear Differential Side Oil SealREPLACEMENT1. Remove the rear differential. Rear Differential (T-type) > REMOVAL"> Rear Differential (VA-type) > REMOVAL">2. Remove the rear differential side oil seal using a ST or screwdriver wrapped with vinyl tape to preve ...
Dtc c0022 front right abs sensor signal
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C0022 FRONT RIGHT ABS SENSOR SIGNALNOTE:For the diagnostic procedure, refer to “DTC C0028 REAR LEFT ABS SENSOR SIGNAL”. Diagnostic Procedure with Diagnostic Trouble Code (DTC) &g ...
