Subaru Crosstrek Service Manual: List
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Read Current Data
LIST
• «Subaru Rear Vehicle Detection (LH)»
Display | Content | Reference value | Note |
SRVD System fail flag | Current failure status of BSD/RCTA system is displayed. |
• Normal
• Fail
—
SRVD System HALT flag
Current temporary stop status of BSD/RCTA system is displayed.
Temporary stop: Temporarily stops when reception of radar sensor waves failed due to some obstacles or when the temperature is not within the range of −40°C (−40°F) — 85°C (185°F).
• Normal
• Halt
—
SRVD System ON-OFF flag
ON/OFF status of BSD/RCTA system is displayed. If this flag is set to «OFF» while the values of «SRVD System fail flag» and «SRVD System HALT flag» are «Normal», the BSD/RCTA system is set to OFF by the BSD/RCTA OFF switch.
• OFF
• ON
—
LH-Side Target detection flag
Detection status of the control target vehicle on the rear left side is displayed.
Detection is possible if the target vehicle is moving when the own vehicle drives forward at 12 km/h (8 MPH) or more or backward at 0 km/h (0 MPH) or more.
• Un-detect
• Detect
—
LH-Side BSD caution 1st flag
ON is displayed when the 1st stage BSD warning on the left side is activated (when the outer mirror assembly illuminates).
• OFF
• ON
—
LH-Side LCA caution 1st flag
ON is displayed when the 1st stage LCA warning on the left side is activated (when the outer mirror assembly illuminates).
• OFF
• ON
—
LH-Side RCTA caution flag
ON is displayed when the RCTA warning on the left side is activated (when the outer mirror assembly illuminates and buzzer sounds).
• OFF
• ON
—
LH-Side Radar Voltage value
Power supply voltage of the radar sensor LH is displayed.
0 — 25.5 V
—
LH-Side Temperature value
Ambient temperature of the radar sensor LH is displayed.
−128 — 127°C
—
Ignition SW ON Count
Time stamp information General Description > CAUTION">
—
—
Count
—
—
Time Count
—
—
• «Subaru Rear Vehicle Detection (RH)»
Display | Content | Reference value | Note |
SRVD System fail flag | Current failure status of BSD/RCTA system is displayed. |
• Normal
• Fail
—
SRVD System HALT flag
Current temporary stop status of BSD/RCTA system is displayed.
Temporary stop: Temporarily stops when reception of radar sensor waves failed due to some obstacles or when the temperature is not within the range of −40°C (−40°F) — 85°C (185°F).
• Normal
• Halt
—
SRVD System ON-OFF flag
ON/OFF status of BSD/RCTA system is displayed. If this flag is set to «OFF» while the values of «SRVD System fail flag» and «SRVD System HALT flag» are «Normal», the BSD/RCTA system is set to OFF by the BSD/RCTA OFF switch.
• OFF
• ON
—
RH-Side Target detection flag
Detection status of the control target vehicle on the rear right side is displayed.
Detection is possible if the target vehicle is moving when the own vehicle drives forward at 12 km/h (8 MPH) or more or backward at 0 km/h (0 MPH) or more.
• Un-detect
• Detect
—
RH-Side BSD caution 1st flag
ON is displayed when the 1st stage BSD warning on the right side is activated (outer mirror assembly illuminates).
• OFF
• ON
—
RH-Side LCA caution 1st flag
ON is displayed when the 1st stage LCA warning on the right side is activated (outer mirror assembly illuminates).
• OFF
• ON
—
RH-Side RCTA caution flag
ON is displayed when the RCTA warning on the right side is activated (when the outer mirror assembly illuminates and buzzer sounds).
• OFF
• ON
—
RH-Side Radar Voltage value
Power supply voltage of the radar sensor RH is displayed.
0 — 25.5 V
—
RH-Side Temperature value
Ambient temperature of the radar sensor RH is displayed.
−128 — 127°C
—
Ignition SW ON Count
Time stamp information General Description > CAUTION">
—
—
Count
—
—
Time Count
—
—
Operation
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Read Current DataOPERATION1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle i ...
Other materials:
Assembly
DRIVE SHAFT SYSTEM > Front Drive ShaftASSEMBLY1. Roll up a thick piece of paper to a size where the shaft can pass through, and affix with tape to form a cylinder.2. Attach a new O-ring on this cylinder.CAUTION:• Always use a new O-ring.• Be careful that the O-ring does not become scr ...
Removal
GLASS/WINDOWS/MIRRORS > Rear Quarter GlassREMOVAL1. Disconnect the ground cable from battery. NOTE">2. Remove the trim panel - rear pillar UPR. Rear Quarter Trim > REMOVAL">3. Remove the glass - rear quarter in the same procedure as for the glass - front window. Windshield G ...
Inspection
VEHICLE DYNAMICS CONTROL (VDC) > Front ABS Wheel Speed SensorINSPECTION1. CHECK WITH SUBARU SELECT MONITOR1. Connect the Subaru Select Monitor to data link connector.NOTE:For detailed operation procedures, refer to “Application help”.(1) On «Start» display, select «Diagnosis».(2) ...
