Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Electrical specification

LAN SYSTEM (DIAGNOSTICS) > Control Module I/O Signal

ELECTRICAL SPECIFICATION

Body integrated unit

For I/O signals of the body integrated unit, refer to BODY CONTROL SYSTEM (DIAGNOSTICS). Control Module I/O Signal">

Engine CM

For I/O signals of ECM, refer to ENGINE (DIAGNOSTICS). Engine Control Module (ECM) I/O Signal">

Transmission CM

For I/O signals of TCM, refer to AUTOMATIC TRANSMISSION (DIAGNOSTICS). Transmission Control Module (TCM) I/O Signal">

VDC CM, steering angle sensor

For I/O signals of VDC CM and steering angle sensor, refer to VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS). Control Module I/O Signal">

Power steering CM

For unit I/O signals of power steering CM, refer to POWER ASSISTED SYSTEM (POWER STEERING) (DIAGNOSTICS). Control Module I/O Signal">

A/C control panel

For unit I/O signals of A/C control panel, refer to HVAC SYSTEM (DIAGNOSTICS). Auto A/C Control Module I/O Signal">

Combination meter

For I/O signals of combination meter, refer to INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS). Control Module I/O Signal">

Airbag CM

For I/O signals of the airbag CM, refer to AIRBAG SYSTEM (DIAGNOSTICS). Airbag Control Module I/O Signal">

High grade MFD

For I/O signals of high grade MFD, refer to INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS). Control Module I/O Signal">

Auto headlight beam leveler CM

For I/O signals of auto headlight beam leveler CM, refer to INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS). Control Module I/O Signal">

Keyless access CM

For I/O signals of keyless access CM, refer to KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS). Control Module I/O Signal">

Stereo camera

For I/O signals of stereo camera, refer to EyeSight (Diagnostics). Control Module I/O Signal">

Radar sensor

For I/O signals of the radar sensor, refer to BSD/RCTA (DIAGNOSTICS). Control Module I/O Signal">

Data communication module

For I/O signals of data communication module, refer to TELEMATICS (DIAGNOSTICS). Control Module I/O Signal">

Data link connector

For I/O signals of data link connector, refer to ENGINE (DIAGNOSTICS). Data Link Connector">

* CAN sleep state:

Hold on for approx. one minute with ignition OFF and the doors, trunk, rear gate all closed.

Control module i/o signal
...

Wiring diagram
LAN SYSTEM (DIAGNOSTICS) > Control Module I/O SignalWIRING DIAGRAMRefer to “CAN Communication System” in the wiring diagram. CAN Communication System > WIRING DIAGRAM"> ...

Other materials:

Removal
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES)(H4DO) > EGR CoolerREMOVAL1. Disconnect the ground cable from battery.2. Drain engine coolant. Engine Coolant > REPLACEMENT">3. Remove the center exhaust pipe. Center Exhaust Pipe > REMOVAL">4. Lower the vehicle.5. Remove the ...

Adjustment
CLUTCH SYSTEM > Clutch SwitchADJUSTMENT1. Loosen the lock nut of the clutch start switch.(A)Lock nut(B)Clutch start switch2. Disconnect the harness connector of the clutch start switch.3. Remove the snap pin and clevis pin connecting the clutch pedal and operating rod.(A)Clevis pin(B)Snap pin(C)P ...

Dtc b2789 id code box communication
KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2789 ID CODE BOX COMMUNICATIONDTC detecting condition:• When communication between keyless access CM and ID code box is interrupted for a set amount of time.• Open ...

© 2016-2025 Copyright www.sucross.com