Subaru Crosstrek Service Manual: Dtc u1433 invalid data received from eyesight

DTC DETECTING CONDITION:

Defective data was transmitted from stereo camera.

TROUBLE SYMPTOM:

Cooperation control of EyeSight does not operate properly.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is DTC for the bus off or the data no-receive displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 4.

4.CHECK DTC.

Check the displayed DTC.

Is U1433 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 9.

5.CHECK DTC.

1) Turn the ignition switch to OFF.

2) Disconnect the stereo camera connector.

3) Connect the disconnected connectors.

4) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U1433 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 6.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 9.

6.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the EyeSight data abnormal detected in several modules?

Replace the stereo camera. Stereo Camera">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 7.

7.REPLACE MODULE.

1) Replace the stereo camera.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U1433 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 8.

System is normal.

8.CHECK MODULE.

1) Reinstall the stereo camera.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U1433 a current malfunction?

Replace the stereo camera. Stereo Camera">

System is normal.

9.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Using the Subaru Select Monitor, read DTC of CAN system. Read Diagnostic Trouble Code (DTC)">

Is U1433 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 10.

10.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Dtc u0100 lost communication with ecm/pcm a

Dtc u0101 lost communication with tcm

Other materials:

Dtc b28a3 eyesight communication(meter)
EyeSight (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B28A3 EyeSight COMMUNICATION(METER)Detected when the combination meter detects the malfunction of stereo camera.DTC DETECTING CONDITION:• Defective CAN system• Defective combination meter• Defect ...

Installation
LIGHTING SYSTEM > Turn Signal Light & Hazard Light UnitINSTALLATIONCAUTION:Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">Install each part in the reve ...

Control module i/o signal Electrical specification
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > Control Module I/O SignalELECTRICAL SPECIFICATION• Combination meterTerminal No.ContentTerminal No.Content1Security indicator27Ambient sensor2Charge warning light28UART (MFD)3Oil pressure warning light29Steering switch (+)4RH turn indicator30Pedes ...