Subaru Crosstrek Service Manual: Dtc u0101 lost communication with tcm

DTC detecting condition:

No data is received from TCM.

Trouble symptom:

Cooperation control with transmission is not performed.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is U0101 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 4.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 8.

4.CHECK DTC.

1) Check CAN communication circuit. CAN Communication Circuit Check">

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0101 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 8.

5.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the transmission data no-receive detected in several modules?

Replace the TCM. Transmission Control Module (TCM)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 6.

6.REPLACE MODULE.

1) Replace the TCM.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0101 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 7.

System is normal.

7.CHECK MODULE.

1) Reinstall the TCM.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0101 a current malfunction?

Replace the TCM. Transmission Control Module (TCM)">

System is normal.

8.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0101 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 9.

9.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Dtc u1433 invalid data received from eyesight

Dtc u1232 lost communication with rear/side radar control module

Other materials:

65
CRUISE CONTROL SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Cancel Code65Cruise control command switch malfunction is detected.While the command switch is pressed ON for a long time (approximately two minutes), stuck ON condition is detected.TROUBLE SYMPTOM:• Cruise control cannot be se ...

Shift lock release using the shift lock release button
Perform the following procedure to release the shift lock. 1. Apply the parking brake and turn the ignition switch to the "LOCK"/"OFF" position. 2. Wrap the tip of a flat-head screwdriver with vinyl tape or a cloth and use it to remove the shift lock cover. The shift lock release button ...

Inspection
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Front Differential AssemblyINSPECTIONRepair or replace the differential gear in the following cases:• When the hypoid driven gear and drive pinion shaft tooth surfaces are damaged, excessively worn, or seized.• When the roller bearing on the ...