Subaru Crosstrek Service Manual: Dtc u1232 lost communication with rear/side radar control module

DTC DETECTING CONDITION:

No data is received from radar sensor.

TROUBLE SYMPTOM:

Radar sensor does not operate normally.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 8?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1232 LOST COMMUNICATION WITH REAR/SIDE RADAR CONTROL MODULE">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1232 LOST COMMUNICATION WITH REAR/SIDE RADAR CONTROL MODULE">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is U1232 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1232 LOST COMMUNICATION WITH REAR/SIDE RADAR CONTROL MODULE">Go to Step 4.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1232 LOST COMMUNICATION WITH REAR/SIDE RADAR CONTROL MODULE">Go to Step 8.

4.CHECK DTC.

1) Check CAN communication circuit. CAN Communication Circuit Check">

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U1232 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1232 LOST COMMUNICATION WITH REAR/SIDE RADAR CONTROL MODULE">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1232 LOST COMMUNICATION WITH REAR/SIDE RADAR CONTROL MODULE">Go to Step 8.

5.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the radar data no-receive detected in several modules?

Replace the radar sensor LH. Radar Sensor">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1232 LOST COMMUNICATION WITH REAR/SIDE RADAR CONTROL MODULE">Go to Step 6.

6.REPLACE MODULE.

1) Replace the radar sensor LH.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U1232 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1232 LOST COMMUNICATION WITH REAR/SIDE RADAR CONTROL MODULE">Go to Step 7.

System is normal.

7.CHECK MODULE.

1) Reinstall the radar sensor LH.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U1232 a current malfunction?

Replace the radar sensor LH. Radar Sensor">

System is normal.

8.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U1232 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1232 LOST COMMUNICATION WITH REAR/SIDE RADAR CONTROL MODULE">Go to Step 9.

9.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC. Clear Memory Mode">

Dtc u0101 lost communication with tcm

Dtc u0122 lost communication with vehicle dynamics control module

Other materials:

Dtc p0020 "a" camshaft position actuator control circuit/open bank 2
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0020 "A" CAMSHAFT POSITION ACTUATOR CONTROL CIRCUIT/OPEN BANK 2DTC detecting condition:Immediately at fault recognitionTrouble symptom:Improper idlingCAUTION:After servicing or replacing faulty part ...

Adjustment
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Extension CaseADJUSTMENTNOTE:When replacing the extension case, select the transfer drive gear shim and transfer driven gear shim. Reduction Drive Gear > ADJUSTMENT"> Transfer Clutch > ADJUSTMENT"> ...

Operation
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > User CustomizingOPERATION1. COMBINATION METER1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».3. On «Main Menu» display, select «Each System».4. On «Sel ...