Subaru Crosstrek Service Manual: Dtc u0100 lost communication with ecm/pcm a

DTC DETECTING CONDITION:

No data is received from ECM.

TROUBLE SYMPTOM:

Cooperation control of transmission may not operate properly.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is U0100 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 4.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 8.

4.CHECK DTC.

1) Check CAN communication circuit. CAN Communication Circuit Check">

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0100 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 8.

5.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the engine data no-receive detected in several modules?

Replace the ECM. Engine Control Module (ECM)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 6.

6.REPLACE MODULE.

1) Replace the ECM.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0100 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 7.

System is normal.

7.CHECK MODULE.

1) Reinstall the ECM.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0100 a current malfunction?

Replace the ECM. Engine Control Module (ECM)">

System is normal.

8.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0100 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 9.

9.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Diagnostic procedure with diagnostic trouble code (dtc)

Dtc u1433 invalid data received from eyesight

Other materials:

Dtc p0202 cylinder 2 injector "a" circuit
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0202 CYLINDER 2 INJECTOR "A" CIRCUITNOTE:For the diagnostic procedure, refer to DTC P0201. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0201 CYLINDER 1 INJECTOR "A" C ...

15
CRUISE CONTROL SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Cancel Code15Detected when CANCEL switch is pressed or malfunction related to CRUISE switch occurs.TROUBLE SYMPTOM:• Cruise control cannot be set. (Cancelled immediately.)• Cruise control cannot be released.Refer to DTC 1 ...

Headlight flasher
CAUTION Do not hold the lever in the flashing position for more than just a few seconds. To flash the headlights, pull the lever toward you and then release it. The high beam will stay on for as long as you hold the lever. The headlight flasher works even though the lighting switch is in ...