Subaru Crosstrek Service Manual: Dtc u0452 invalid data received from restraints control module

DTC DETECTING CONDITION:

Invalid data was transmitted from airbag CM.

TROUBLE SYMPTOM:

Cooperation control with airbag does not operate properly.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0452 INVALID DATA RECEIVED FROM RESTRAINTS CONTROL MODULE">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0452 INVALID DATA RECEIVED FROM RESTRAINTS CONTROL MODULE">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is DTC for the bus off or the data no-receive displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0452 INVALID DATA RECEIVED FROM RESTRAINTS CONTROL MODULE">Go to Step 4.

4.CHECK DTC.

Check the displayed DTC.

Is U0452 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0452 INVALID DATA RECEIVED FROM RESTRAINTS CONTROL MODULE">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0452 INVALID DATA RECEIVED FROM RESTRAINTS CONTROL MODULE">Go to Step 9.

5.CHECK DTC.

1) Turn the ignition switch to OFF.

2) Disconnect the airbag CM connector.

3) Connect the disconnected connectors.

4) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0452 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0452 INVALID DATA RECEIVED FROM RESTRAINTS CONTROL MODULE">Go to Step 6.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0452 INVALID DATA RECEIVED FROM RESTRAINTS CONTROL MODULE">Go to Step 9.

6.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the airbag data abnormal detected in several modules?

Replace the airbag CM. Airbag Control Module">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0452 INVALID DATA RECEIVED FROM RESTRAINTS CONTROL MODULE">Go to Step 7.

7.REPLACE MODULE.

1) Replace the airbag CM.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0452 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0452 INVALID DATA RECEIVED FROM RESTRAINTS CONTROL MODULE">Go to Step 8.

System is normal.

8.CHECK MODULE.

1) Reinstall the airbag CM.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0452 a current malfunction?

Replace the airbag CM. Airbag Control Module">

System is normal.

9.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Using the Subaru Select Monitor, read DTC of CAN system. Read Diagnostic Trouble Code (DTC)">

Is U0452 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0452 INVALID DATA RECEIVED FROM RESTRAINTS CONTROL MODULE">Go to Step 10.

10.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Dtc u0428 invalid data received from steering angle sensor module

Dtc u1120 lost communication with autostart stop control module

Other materials:

Dtc p0724 brake switch "b" circuit high
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0724 BRAKE SWITCH "B" CIRCUIT HIGHDTC detecting condition:Immediately at fault recognitionTrouble symptom:Gear is not shifted down when climbing a hill or driving down a hill.C ...

Dtc b1407 met communication
IMMOBILIZER (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B1407 MET COMMUNICATIONDTC DETECTING CONDITION:Communication failure between body integrated unit and combination meterCAUTION:When the combination meter is replaced, registration of the immobilizer system is r ...

Operation
TELEMATICS SYSTEM (DIAGNOSTICS) > Subaru Select MonitorOPERATION• For detailed operation procedures, refer to “Application help”.• When DCM cannot establish communication with Subaru Select Monitor, perform “COMMUNICATION FOR INITIALIZING IMPOSSIBLE”. Subaru S ...