Subaru Crosstrek Service Manual: Dtc p2004 tgv control stuck open bank 1

Subaru Crosstrek Service Manual / Engine (diagnostics)(h4do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p2004 tgv control stuck open bank 1

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P2004 TGV CONTROL STUCK OPEN BANK 1

DTC DETECTING CONDITION:

Immediately at fault recognition

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

STEP	CHECK	YES	NO

1.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check the appropriate DTC using the “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2004 TGV CONTROL STUCK OPEN BANK 1">Go to Step 2.

2.CHECK TUMBLE GENERATOR VALVE RH.

1) Remove the tumble generator valve assembly RH.

2) Check the tumble generator valve.

Is there any dirt or clogging with foreign objects in the tumble generator valve?

Clean the tumble generator valve.

Replace the tumble generator valve RH. Tumble Generator Valve Assembly">

1. OUTLINE OF DIAGNOSIS

Detect the malfunction of tumble generator valve motor function.

Judge open fixing malfunction when the opening degree is large even after finishing the tumble generator valve closing driving.

2. EXECUTION CONDITION

Secondary Parameters	Execution condition
Battery voltage	≥ 10.9 V
Tumble generator valve “close” signal output time	≥ 1600 ms

3. GENERAL DRIVING CYCLE

Always perform the diagnosis continuously.

4. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria	Threshold Value
TGV position	= Open
As defined by: TGV angle position sensor voltage > = 2.5 V

Malfunction Criteria

Threshold Value

TGV position

= Open

As defined by:

TGV angle position sensor voltage > = 2.5 V

Time Needed for Diagnosis: 3000 ms

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p1499 coil 4 egr "a" control circuit high

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P1499 COIL 4 EGR "A" CONTROL CIRCUIT HIGHDTC detecting condition:Immediately at fault recognitionTr ...

Dtc p2005 tgv control stuck open bank 2

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2005 TGV CONTROL STUCK OPEN BANK 2DTC DETECTING CONDITION:Immediately at fault recognitionCAUTION:After serv ...

Other materials:

Dtc u0422 invalid data received from body control module
LAN SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0422 INVALID DATA RECEIVED FROM BODY CONTROL MODULEDTC DETECTING CONDITION:Defective data was transmitted from body integrated unit.TROUBLE SYMPTOM:Cooperation control with body integrated unit does not operate ...

Installation
CLUTCH SYSTEM > Release Bearing and LeverINSTALLATIONNOTE:Apply the specified grease to lubricate to the following points before installation.• Contact surface of lever and pivot• Contact surface of lever and bearing• Transmission main shaft spline• Contact surface of rele ...

Charge warning light
If this light illuminates when the engine is running, it may indicate that the charging system is not working properly. If the light illuminates while driving or does not turn off after the engine starts, stop the engine at the first safe opportunity and check the alternator belt. If the ...