Subaru Crosstrek Service Manual: Dtc c0045 incorrect vdc control module specifications

DTC detecting condition:

Different control module specification

Trouble symptom:

• ABS does not operate.

• VDC does not operate.

• EyeSight does not operate.

When parameter selection for VDCCM is improper, this DTC may be memorized.

1.CHECK VDCCM&H/U IDENTIFICATION SYMBOL.

Check the identification symbol attached on the H/U. General Description > SPECIFICATION">

Is the identification symbol correct?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0045 INCORRECT VDC CONTROL MODULE SPECIFICATIONS">Go to Step 2.

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

2.CHECK PARAMETER SELECTED IN VDCCM.

Subaru Select Monitor > OPERATION">

Does the parameter registered in the VDCCM match the relevant vehicle?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0045 INCORRECT VDC CONTROL MODULE SPECIFICATIONS">Go to Step 3.

Select and register the correct parameter. Subaru Select Monitor > OPERATION">

3.CHECK TCM SPECIFICATION.

Check the TCM specification.

Is the specification of TCM same as vehicle specification?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0045 INCORRECT VDC CONTROL MODULE SPECIFICATIONS">Go to Step 4.

Replace the TCM. Transmission Control Module (TCM)">

4.CHECK CVT SYSTEM.

1) Start the engine.

2) Read the DTC of the CVT system. Read Diagnostic Trouble Code (DTC)">

Is DTC of CVT system displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0045 INCORRECT VDC CONTROL MODULE SPECIFICATIONS">Go to Step 5.

5.CHECK ECM SPECIFICATION.

Check the ECM specification.

Is the specification of ECM same as vehicle specification?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0045 INCORRECT VDC CONTROL MODULE SPECIFICATIONS">Go to Step 6.

Replace the ECM. Engine Control Module (ECM)">

6.CHECK ENGINE SYSTEM.

1) Start the engine.

2) Read DTC of the engine system. Read Diagnostic Trouble Code (DTC)">

Is engine system DTC displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0045 INCORRECT VDC CONTROL MODULE SPECIFICATIONS">Go to Step 7.

7.CHECK VDCCM&H/U.

1) Perform the Clear Memory Mode. Clear Memory Mode">

2) Perform the Inspection Mode. Inspection Mode">

3) Read the DTC. Read Diagnostic Trouble Code (DTC)">

Is the same DTC displayed?

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0045 INCORRECT VDC CONTROL MODULE SPECIFICATIONS">Go to Step 8.

8.CHECK DETECTION OF OTHER DTCS FOR VDC.

Read Diagnostic Trouble Code (DTC)">

Is any other DTC displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.

Dtc c0057 ecm control system

Dtc c0045 tcm malfunction

Other materials:

Removal
REAR SUSPENSION > Front Lateral LinkREMOVAL1. Lift up the vehicle, and then remove the rear wheels.2. Remove the bolts and nuts, and then remove the trailing link.3. Remove the lateral link assembly - front.(1) Remove the snap pin (a) and nut (b).(2) Remove the ball joint from the housing assembl ...

Removal
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Oil Control SolenoidREMOVALCAUTION:If the engine oil is spilt over exhaust pipe or the under cover, wipe it off with cloth to avoid emission of smoke or causing a fire.1. INTAKE SIDE1. Disconnect the ground cable from battery.2. Remove the air intake duct. (R ...

Camera adjustment, inspection Procedure
EyeSight > Camera Adjustment, InspectionPROCEDURECAUTION:• Perform the camera adjustment and inspection at curb weight without passengers.• Handle RANDOM CHART (ST) carefully so as not to break it with the adhesive force of the tape.Perform inspection or adjustment according to the fo ...