Subaru Crosstrek Service Manual: Dtc b1822 short in side airbag rh (to ground)

Diagnosis start condition:

Ignition voltage is 10 V to 16 V.

DTC detecting condition:

• Side airbag harness (RH) circuit is shorted to ground.

• Side airbag module (RH) is faulty.

• Airbag control module is faulty.

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">

1.CHECK POOR CONTACT OF CONNECTORS.

Check for poor contact of the connectors between the airbag control module, side airbag module RH and the side airbag sensor RH.

Is there poor contact?

Replace the airbag rear harness along with body harness.

Diagnostic Chart with Trouble Code > DTC B1822 SHORT IN SIDE AIRBAG RH (TO GROUND)">Go to Step 2.

2.CHECK SIDE AIRBAG MODULE.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB24), and connect the connector (1AJ) in test harness AJ to connector (AB24).

3) Connect the airbag resistor to the test harness AJ connector (3AJ).

4) Connect the battery ground terminal and turn the ignition switch to ON.

Does the airbag warning light illuminate for six seconds and go off?

Replace the side airbag module (RH). Side Airbag Module > REMOVAL">

Diagnostic Chart with Trouble Code > DTC B1822 SHORT IN SIDE AIRBAG RH (TO GROUND)">Go to Step 3.

3.CHECK AIRBAG REAR HARNESS (SIDE AIRBAG MODULE HARNESS RH).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB26) from seat belt pretensioner (RH).

3) Disconnect the connector (AB33) from curtain airbag module (RH).

4) Disconnect the airbag resistor from test harness AJ.

5) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.

6) Connect the connector (1AG) in the test harness AG to the connectors (AB6, AB17, AB18).

7) Measure the resistance between connector (5AG) in the test harness AG and chassis ground.

Connector & terminal

(5AG) No. 5 — Chassis ground:

(5AG) No. 7 — Chassis ground:

Is the resistance 1 M? or more?

Diagnostic Chart with Trouble Code > DTC B1822 SHORT IN SIDE AIRBAG RH (TO GROUND)">Go to Step 4.

Replace the airbag rear harness along with body harness.

4.CHECK AIRBAG CONTROL MODULE.

1) Connect all connectors.

2) Clear the memory. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">

Is DTC B1822 displayed?

Replace the airbag control module. Airbag Control Module">

Diagnostic Chart with Trouble Code > DTC B1822 SHORT IN SIDE AIRBAG RH (TO GROUND)">Go to Step 5.

5.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Finish the diagnosis.

Dtc b1821 open in side airbag rh

Dtc b1823 short in side airbag rh (to +b)

Other materials:

Inspection
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Transmission Gear OilINSPECTION1. Park the vehicle on a level surface.2. Turn the ignition switch to OFF, and wait until the engine cools.3. Remove the oil level gauge and wipe it clean.4. Reinsert the oil level gauge all the way. Be sure that the oil l ...

Operation
POWER ASSISTED SYSTEM (POWER STEERING) (DIAGNOSTICS) > Subaru Select MonitorOPERATION1. HOW TO USE SUBARU SELECT MONITORFor detailed operation procedures, refer to “Application help”.2. READ CURRENT DATA1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, ...

Bulkhead wiring harness (in compartment) Location
WIRING SYSTEM > Bulkhead Wiring Harness (In Compartment)LOCATIONConnectorConnecting toNo.PoleColorAreaNo.DescriptionB274B-4 Blower Resistor (manual A/C)B308BlackC-5 Front door cord RHB3110GrayC-1AB1Airbag wiring harnessB328B-2 Turn signal and hazard unitB4016BlackC-1 Data link connectorB412C-2 Po ...