Subaru Crosstrek Service Manual: Check list for interview Check

Subaru Crosstrek Service Manual / Vehicle dynamics control (vdc) (diagnostics) / Check list for interview Check

VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Check List for Interview

CHECK

Check the following item about the vehicle’s state.

1. STATE OF ABS WARNING LIGHT

ABS warning light illuminates.	Always Sometimes Only once Does not illuminate • When/How long does it illuminate?
Ignition key position	LOCK ACC ON (before starting engine) START ON (after starting engine, engine is running) ON (after starting engine, engine is at a standstill)
Timing	Immediately after turning the ignition switch to ON Immediately after turning the ignition switch to START
	While accelerating	—	km/h
		—	MPH
	While driving at a constant speed	km/h	MPH
	While decelerating	—	km/h
		—	MPH
	When turning to the right	Steering angle:	deg
		Steering time:	Sec.
	When turning to the left	Steering angle:	deg
		Steering time:	Sec.
	When other electrical parts are operating
	• Part name: • Operating condition:

2. STATE OF VDC WARNING LIGHT & VDC INDICATOR LIGHT

VDC warning light & VDC indicator light illuminates.	Always Sometimes Only once Does not illuminate • When/How long does it illuminate?
Ignition key position	LOCK ACC ON (before starting engine) START ON (after starting engine, engine is running) ON (after starting engine, engine is at a standstill)
Timing	Immediately after turning the ignition switch to ON Immediately after turning the ignition switch to START
	While accelerating	—	km/h
		—	MPH
	While driving at a constant speed	km/h	MPH
	While decelerating	—	km/h
		—	MPH
	When turning to the right	Steering angle:	deg
		Steering time:	Sec.
	When turning to the left	Steering angle:	deg
		Steering time:	Sec.
	When other electrical parts are operating
	• Part name: • Operating condition:

3. STATE OF VDC OFF INDICATOR LIGHT

VDC OFF indicator light illuminates.	Always Sometimes Only once Does not illuminate • When/How long does it illuminate?
Ignition key position	LOCK ACC ON (before starting engine) START ON (after starting engine, engine is running) ON (after starting engine, engine is at a standstill)
Timing	Immediately after turning the ignition switch to ON Immediately after turning the ignition switch to START
	While accelerating	—	km/h
		—	MPH
	While driving at a constant speed	km/h	MPH
	While decelerating	—	km/h
		—	MPH
	When turning to the right	Steering angle:	deg
		Steering time:	Sec.
	When turning to the left	Steering angle:	deg
		Steering time:	Sec.
	When other electrical parts are operating
	• Part name: • Operating condition:

4. CONDITIONS UNDER WHICH TROUBLE OCCURS

Environment	a) Weather	Fine Cloudy Rainy Snowy Others:
	b) Ambient temperature	°C (°F)
	c) Road	Inner city Suburbs Highway Local street Uphill Downhill Paved road Gravel road Muddy road Sandy place Straight road Sharp curve Gentle curve S-curve Road with a slope on both sides Others:
	d) Road surface	Dry Wet Covered with fresh snow Covered with hardened snow Frozen slope Others:
Condition	a) Brakes	Deceleration:	G
		continuous / intermittent
	b) Accelerator	Acceleration:	G
		continuous / intermittent
	c) Vehicle speed	km/h	MPH
		Advancing While accelerating While decelerating At low speed When turning Others:
	d) Tire inflation pressure	Front RH tire:	kPa
		Front LH tire:	kPa
		Rear RH tire:	kPa
		Rear LH tire:	kPa
	e) Degree of wear	Front RH tire:	mm (in)
		Front LH tire:	mm (in)
		Rear RH tire:	mm (in)
		Rear LH tire:	mm (in)
	f) Steering wheel	Sharp turning Gentle turning Straight forward motion Gentle return Sharp return
	g) Tire/Wheel size	Specified size Except specification ( )
	h) Tire variation	Summer tire Studless tire (Brand: )
	i) Tire chain is attached: Yes / No
	j) Using T-type tires: Yes / No
	k) Condition of suspension alignment:
	l) Load condition:
	m) Repaired parts are used: Yes / No
	• Content:
	n) Others:

Basic diagnostic procedure Procedure

VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Basic Diagnostic ProcedurePROCEDURECAUTION:Remove foreign matter (dust, water, oil etc.) from the VDCCM&H/U connector during removal and installat ...

Clear memory mode Operation

VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Clear Memory ModeOPERATION1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the vehicle information and select ...

Other materials:

Engine oil
CAUTION If the oil level gauge in your Subaru Ascent does not slide out easily, gently rotate it left and right before pulling. Applying excessive force may lead to sudden release and possible injury. Always use engine oil that meets the recommended grade and viscosity specified for t ...

Brake line Inspection
PERIODIC MAINTENANCE SERVICES > Brake LineINSPECTION1. BRAKE LINE1. Check for scratches, swelling, corrosion, traces of fluid leakage on the brake hoses or pipe joints.2. Make sure that brake pipes/hoses do not interfere with adjacent parts and there is no loose connector/clamp during driving.3. ...

General diagnostic table Inspection
WHEEL AND TIRE SYSTEM > General Diagnostic TableINSPECTIONSymptomsPossible causeCorrective actionWheel is out of balance.Improperly inflated tire.Adjust the tire pressure.Uneven wearCheck the tire referring to “Abnormal tire wear” in this table, carry out the procedure and replace the ...