Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Specification

POWER ASSISTED SYSTEM (POWER STEERING) > General Description

SPECIFICATION

Whole system

Minimum turning radius

m (ft)

5.3 (17.4)

Steering angle

Inner wheel

38.2°±1.5°

Outer wheel

33.6°±1.5°

Steering wheel diameter

mm (in)

375 (14.76)

Lock-to-lock revolution number

2.8

Gearbox

Type

Rack and Pinion, Integral

Backlash

0 (automatic adjusting)

Power steering motor

Motor

(Temperature 20°C (68°F))

Rated voltage

V

12

Rated torque

N·m (kgf-m, ft-lb)

4.5 (0.46, 3.31)

Rated revolution speed

r/min

1,140

Rated current

A

85

Rated output

W

561

Steering wheel

Free play

mm (in)

17 (0.67) or less

Column assembly - steering

Clearance

Between steering wheel and cover assembly - column

mm (in)

4 — 6 (0.16 — 0.24)

Steering gearbox

Sliding resistance

N (kgf, lbf)

303 (31, 68) or less

Difference between right and left sliding resistance: 20% or less

Rack shaft play in the radial direction

mm (in)

Right-turn steering

Both amplitudes: 0.6 (0.024) or less

Left-turn steering

Both amplitudes: 0.4 (0.016) or less

Input shaft play

mm (in)

In radial direction

Both amplitudes: 0.18 (0.0071) or less

In axial direction

0.27 (0.0106) or less

Rotational resistance

N (kgf, lbf)

Maximum allowable value: 18.0 (1.8, 4.0) or less

Difference between right and left sliding resistance: 20% or less

Steering effort (with power steering assist)

At standstill with engine idling on paved road

N (kgf, lbf)

29.4 (3.0, 6.6) or less

At standstill with engine stalled on paved road

N (kgf, lbf)

294.2 (30, 66.2) or less

Caution
POWER ASSISTED SYSTEM (POWER STEERING) > General DescriptionCAUTION• Wear appropriate work clothing, including a helmet, protective goggles and protective shoes when performing any work.&bull ...

Component
POWER ASSISTED SYSTEM (POWER STEERING) > General DescriptionCOMPONENT1. STEERING WHEEL AND COLUMN(1)Bushing(7)Cover - steering wheel LWR(13)Airbag module(2)Column ASSY - steering(8)MID switch (3)S ...

Other materials:

Installation
EXTERIOR/INTERIOR TRIM > Front BumperINSTALLATION1. Install each part in the reverse order of removal.2. Secure the flange section of the bumper face - front to the bracket - front bumper side.CAUTION:• Install so that the front end of the under cover (b) comes inside the bumper face - fron ...

Removal
LUBRICATION(H4DO) > Oil Level SwitchREMOVAL1. Open the front hood, and make alignment marks (A) on the front hood striker and the front hood using a marker pen.2. Remove the front hood striker from the front hood.3. Change the front hood stay position from (A) to (B), and completely open the fron ...

Installation
EXTERIOR BODY PANELS > Front FenderINSTALLATION1. Install each part in the reverse order of removal.CAUTION:• Install the bumper face - front so that the front end of the under cover (b) comes inside the bumper face - front (a), and the front end of the mud guard (c) comes outside the bumpe ...

© 2016-2025 Copyright www.sucross.com