Subaru Crosstrek Service Manual: Removal
MECHANICAL(H4DO) > Cam Sprocket
REMOVAL
1. CAM SPROCKET RH
NOTE:
When replacing a single part, perform the work with the engine assembly installed to body.
• Intake cam sprocket RH
1. Remove the chain cover. Chain Cover > REMOVAL">
2. Remove the timing chain RH. Timing Chain Assembly > REMOVAL">
3. Hold the intake cam sprocket RH using the ST1 and ST2, and remove the bolts using the ST3.
CAUTION:
Perform the operation carefully since the ST comes off easily.
| ST1 18355AA000 | PULLEY WRENCH |
| ST2 18334AA020 | PULLEY WRENCH PIN SET |
| ST3 18270KA010 | SOCKET |
4. Remove the intake cam sprocket RH.
• Exhaust cam sprocket RH
1. Remove the chain cover. Chain Cover > REMOVAL">
2. Remove the timing chain RH. Timing Chain Assembly > REMOVAL">
3. Hold the exhaust cam sprocket RH using the ST1 and ST2, and remove the bolts using the ST3.
CAUTION:
Perform the operation carefully since the ST comes off easily.
| ST1 18355AA000 | PULLEY WRENCH |
| ST2 18334AA020 | PULLEY WRENCH PIN SET |
| ST3 18270KA010 | SOCKET |
4. Remove the exhaust cam sprocket RH.
2. CAM SPROCKET LH
NOTE:
When replacing a single part, perform the work with the engine assembly installed to body.
• Intake cam sprocket LH
1. Remove the chain cover. Chain Cover > REMOVAL">
2. Remove the timing chain LH. Timing Chain Assembly > REMOVAL">
3. Hold the intake cam sprocket LH using the ST1 and ST2, and remove the bolts using the ST3.
CAUTION:
Perform the operation carefully since the ST comes off easily.
| ST1 18355AA000 | PULLEY WRENCH |
| ST2 18334AA020 | PULLEY WRENCH PIN SET |
| ST3 18270KA010 | SOCKET |
4. Remove the intake cam sprocket LH.
• Exhaust cam sprocket LH
1. Remove the chain cover. Chain Cover > REMOVAL">
2. Remove the timing chain LH. Timing Chain Assembly > REMOVAL">
3. Hold the exhaust cam sprocket LH using the ST1 and ST2, and remove the bolts using the ST3.
CAUTION:
Perform the operation carefully since the ST comes off easily.
| ST1 18355AA000 | PULLEY WRENCH |
| ST2 18334AA020 | PULLEY WRENCH PIN SET |
| ST3 18270KA010 | SOCKET |
4. Remove the exhaust cam sprocket LH.
Inspection
MECHANICAL(H4DO) > Cam SprocketINSPECTIONCheck the cam sprocket teeth for abnormal wear and scratches. ...
Installation
MECHANICAL(H4DO) > Cam SprocketINSTALLATION1. CAM SPROCKET RH• Intake cam sprocket RH1. Install the intake cam sprocket RH by aligning the knock hole (A) of intake cam sprocket RH and the kno ...
Other materials:
Valet mode
When you choose the valet mode, the
alarm system does not operate. In valet
mode, the remote transmitter is used only
for locking and unlocking the doors and
rear gate and panic activation.
To enter the valet mode, change the
setting of your vehicle's alarm system for
deactivation mode. Ref ...
Inspection mode Procedure
ENGINE (DIAGNOSTICS)(H4DO) > Inspection ModePROCEDUREPerform the diagnosis shown in the following DTC table.When performing the diagnosis not listed in “List of Diagnostic Trouble Code (DTC)”, refer to the item on the drive cycle. Drive Cycle">DTCItemConditionB1570ANTENNA — ...
Inspection
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > FRESH/RECIRC Door ActuatorINSPECTION1. CHECK LINK1. Visually check the operation range of the link, and remove the foreign material if any.2. Operate the FRESH/RECIRC switch to check that the link operates normally.3. If it does not operate normally as t ...
