Subaru Crosstrek Service Manual: Inspection

• Standard type

Refer to the following inspection steps. Multi-function Display (MFD) System > INSPECTION">

• High grade type

Refer to “Basic Diagnostic Procedure” of “INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS)” section. Basic Diagnostic Procedure">

(1) Power supply

(2) Ground circuit

(3) Communication circuit harness

(4) MFD

(1) Power supply

(2) Ground circuit

(3) MFD

(1) Power supply

(2) Harness

(3) Ambient sensor

(4) Communication circuit

(5) MFD

(1) Setting

(2) MFD

1.CHECK POWER SUPPLY.

1) Disconnect the MFD connector.

2) Measure the voltage between MFD connector and chassis ground.

Connector & terminal

(i122) No. 1 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Multi-function Display (MFD) System > INSPECTION">Go to Step 2.

Check the harness for open or short between the fuse and MFD.

2.CHECK GROUND CIRCUIT.

Measure the resistance between MFD connector and chassis ground.

Connector & terminal

(i122) No. 2 — Chassis ground:

Is the resistance less than 10 ??

Multi-function Display (MFD) System > INSPECTION">Go to Step 3.

Repair or replace the harness.

3.CHECK HARNESS BETWEEN MFD AND COMBINATION METER ASSEMBLY.

1) Disconnect the connector of combination meter assembly.

2) Check the harness between MFD and combination meter assembly.

Connector & terminal

(i122) No. 9 — (i10) No. 28:

Is harness normal?

Multi-function Display (MFD) System > INSPECTION">Go to Step 4.

Repair or replace the harness.

4.CHECK MFD.

1) Remove the MFD.

2) Attach the clock to another vehicle on which the clock display operates normally, and check its operation.

Is MFD normal?

Replace the meter - main assembly. Combination Meter">

Replace the MFD.

1.CHECK POWER SUPPLY.

1) Disconnect the MFD connector.

2) Turn the ignition switch to ON.

3) Measure the voltage between MFD connector and chassis ground.

Connector & terminal

(i122) No. 3 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Multi-function Display (MFD) System > INSPECTION">Go to Step 2.

Repair or replace the harness.

2.CHECK GROUND CIRCUIT.

Measure the resistance between MFD connector and chassis ground.

Connector & terminal

(i122) No. 2 — Chassis ground:

Is the resistance less than 10 ??

Multi-function Display (MFD) System > INSPECTION">Go to Step 3.

Repair or replace the harness.

3.CHECK MFD.

1) Remove the MFD.

2) Attach the clock to another vehicle on which the clock display operates normally, and check its operation.

Is the MFD normal?

Repair the poor contact of connector.

Replace the MFD.

1.CHECK AMBIENT SENSOR POWER SUPPLY.

1) Disconnect the ambient sensor connector.

2) Turn the ignition switch to ON.

3) Measure the voltage between the ambient sensor connector and chassis ground.

Connector & terminal

(F78) No. 1 (+) — Chassis ground (−):

Is the voltage 4 V or more?

Multi-function Display (MFD) System > INSPECTION">Go to Step 2.

Check the harness for open or short between the fuse and MFD.

2.CHECK HARNESS BETWEEN AMBIENT SENSOR AND COMBINATION METER ASSEMBLY.

1) Disconnect the connector of combination meter assembly.

2) Check harness between ambient sensor and combination meter assembly.

Connector & terminal

(F78) No. 1 — (i10) No. 27:

(F78) No. 2 — (i10) No. 36:

Is harness normal?

Multi-function Display (MFD) System > INSPECTION">Go to Step 3.

Repair or replace the harness.

3.CHECK AMBIENT SENSOR.

Check the ambient sensor. Ambient Sensor > INSPECTION">

Is the ambient sensor operating properly?

Multi-function Display (MFD) System > INSPECTION">Go to Step 4.

Replace the ambient sensor.

4.CHECK AMBIENT TEMPERATURE DISPLAY.

1) Connect the combination meter assembly connector.

2) Install the 3 k? resistance between connector terminals of the ambient sensor.

3) Turn the ignition switch to ON.

Connector & terminal

(F78) No. 1 — No. 2:

Does the ambient temperature display 25°C (77°F)?

Repair the poor contact between the ambient sensor and harness connector.

Multi-function Display (MFD) System > INSPECTION">Go to Step 5.

5.CHECK CURRENT DATA.

Using the Subaru Select Monitor, display the data of «Ambient Air Temperature».

NOTE:

For detailed operation procedures, refer to “Application help”.

Is the ambient temperature of 25°C (77°F) output?

Multi-function Display (MFD) System > INSPECTION">Go to Step 6.

Replace the meter - main assembly. Combination Meter">

6.CHECK MFD.

1) Remove the MFD.

2) Attach the ambient temperature display to another vehicle on which the ambient temperature display operates normally to check its operation.

Does the ambient temperature display 25°C (77°F)?

Replace the MFD.

Replace the meter - main assembly. Combination Meter">

1.CHECK FUEL ECONOMY DISPLAY OFF MODE.

Check that the mode display changes when the MFD changeover knob is operated.

(Display changes in the following order: cruising distance > average fuel economy > instantaneous fuel economy > continuous driving time > average vehicle speed > blank display)

Is fuel economy displayed?

MFD is normal.

Multi-function Display (MFD) System > INSPECTION">Go to Step 2.

2.CHECK MFD.

1) Remove the MFD.

2) Attach the fuel economy display to another vehicle on which the fuel economy display operates normally to check its operation.

Is the fuel economy display correct?

Replace the meter - main assembly. Combination Meter">

Replace the MFD.

Wiring diagram

Note

Other materials:

Transmission
SPECIFICATIONS > CrosstrekTRANSMISSION1. MTModel2.0 L DOHC non-turboTransmission type5MTClutch typeDSPDGear ratio1st3.5452nd1.8883rd1.2964th0.9725th0.780Rev.3.333Reduction gear (front)Type of gearHypoidGear ratio4.444Transfer reductionType of gearHelicalGear ratio1.000Reduction gear (rear)Final r ...

Dtc b1907 short in front p/t lh (to ground)
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B1907 SHORT IN FRONT P/T LH (TO GROUND)Diagnosis start condition:Ignition voltage is 10 V to 16 V.DTC detecting condition:• Seat belt pretensioner (LH) circuit is shorted to ground.• Pretensioner (LH) is faulty.• ...

Removal
SECURITY AND LOCKS > Front Door Latch and Door Lock Actuator AssemblyREMOVAL1. Raise the glass assembly - front door to the top position.2. Disconnect the ground cable from battery and wait for at least 60 seconds before starting work. NOTE">3. Remove the trim panel - front door. Door T ...