Subaru Crosstrek Service Manual: Dtc b1907 short in front p/t lh (to ground)

Diagnosis start condition:

Ignition voltage is 10 V to 16 V.

DTC detecting condition:

• Seat belt pretensioner (LH) circuit is shorted to ground.

• Pretensioner (LH) is faulty.

• Pretensioner harness (LH) is faulty.

• Airbag control module is faulty.

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">

1.CHECK POOR CONTACT OF CONNECTORS.

Check for poor contact of the connectors between the airbag control module and the seat belt pretensioner LH.

Is there poor contact?

Replace the airbag rear harness along with body harness.

Diagnostic Chart with Trouble Code > DTC B1907 SHORT IN FRONT P/T LH (TO GROUND)">Go to Step 2.

2.CHECK SEAT BELT PRETENSIONER.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB21) from seat belt pretensioner (LH).

3) Connect the connector (1N) in the test harness N to the connector (AB21).

4) Connect the airbag resistor to the connector (2N) of test harness N.

5) Connect the battery ground terminal and turn the ignition switch to ON.

Does the airbag warning light illuminate for six seconds and go off?

Replace the seat belt pretensioner (LH). Front Seat Belt">

Diagnostic Chart with Trouble Code > DTC B1907 SHORT IN FRONT P/T LH (TO GROUND)">Go to Step 3.

3.CHECK AIRBAG REAR HARNESS (PRETENSIONER HARNESS LH).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the airbag resistor from the connector (2N) of test harness N.

3) Disconnect connector (AB19) from side airbag module (LH).

4) Disconnect the connector (AB31) from curtain airbag module (LH).

5) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.

6) Connect the connector (1AG) in the test harness AG to the connectors (AB6, AB17, AB18).

7) Measure the resistance between connector (3AG) in the test harness AG and chassis ground.

Connector & terminal

(3AG) No. 10 — Chassis ground:

(3AG) No. 12 — Chassis ground:

Is the resistance 1 M? or more?

Diagnostic Chart with Trouble Code > DTC B1907 SHORT IN FRONT P/T LH (TO GROUND)">Go to Step 4.

Replace the airbag rear harness along with body harness.

4.CHECK AIRBAG CONTROL MODULE.

1) Connect all connectors.

2) Clear the memory. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">

Is DTC B1907 displayed?

Replace the airbag control module. Airbag Control Module">

Diagnostic Chart with Trouble Code > DTC B1907 SHORT IN FRONT P/T LH (TO GROUND)">Go to Step 5.

5.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Finish the diagnosis.

Dtc b1906 open in front p/t lh

Dtc b1610 front sub sensor rh failure

Other materials:

Inspection
REAR SUSPENSION > Rear Shock AbsorberINSPECTION1. Check for oil leaks.2. Move the piston rod up and down to check that it operates smoothly without any hitch.3. Check the piston rod for play as follows:(1) Fix the outer shell in place and fully extend the rod.(2) Set the dial gauge on the end of ...

Installation
LIGHTING SYSTEM > Front Fog Light AssemblyINSTALLATIONCAUTION:Install the mud guard - front so that the front end of the mud guard (b) comes outside the bumper face - front (a).1. Install each part in the reverse order of removal.Tightening torque:Fog light assembly - front: 7.5 N·m (0.76 ...

Manual transmission
The manual transmission is a fully synchromeshed, 5-forward-speed and 1-reverse- speed transmission. The shift pattern is shown on the shift lever knob. When shifting from 5th gear to reverse gear, first return the shift lever to the neutral position then shift into reverse gear. To ...