Subaru Crosstrek Service Manual: Inspection
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > AT OIL TEMP Warning Light Display
INSPECTION
DIAGNOSIS:
• CAN communication is lost with the combination meter.
• Combination meter malfunction
• TCM is in special control mode.
• AT learning is not finished.
TROUBLE SYMPTOM:
• When the ignition switch is turned to ON, the AT OIL TEMP light does not illuminate.
• AT OIL TEMP light remains lit after engine start.
| STEP | CHECK | YES | NO |
1.CHECK DTC.
Read the DTC relating the TCM using the Subaru Select Monitor.
Is DTC U0155 or U0423 displayed?
Perform the self-diagnosis of combination meter.
AT OIL TEMP Warning Light Display > INSPECTION">Go to Step 2.
2.CHECK DTC.
Read the DTC relating the TCM using the Subaru Select Monitor.
Are DTCs other than U0155 and U0423 displayed?
Perform the diagnosis according to DTC.
AT OIL TEMP Warning Light Display > INSPECTION">Go to Step 3.
3.CHECK COMBINATION METER.
Read DTC of combination meter.
Is DTC displayed?
Perform the diagnosis according to DTC.
AT OIL TEMP Warning Light Display > INSPECTION">Go to Step 4.
4.CHECK AT OIL TEMP LIGHT.
Turn the ignition switch to ON.
Does AT OIL TEMP light illuminate and then go off in 2 seconds?
AT OIL TEMP Warning Light Display > INSPECTION">Go to Step 5.
Perform the self-diagnosis of combination meter. Combination Meter System > OPERATION">
5.CHECK AT OIL TEMP LIGHT.
Start the engine.
Does the AT OIL TEMP light go off?
Current condition is normal. Go back to Basic Diagnostic Procedure. Basic Diagnostic Procedure">
AT OIL TEMP Warning Light Display > INSPECTION">Go to Step 6.
6.CHECK DTC.
Read the DTC relating the TCM using the Subaru Select Monitor.
Is DTC displayed?
Perform the diagnosis according to DTC.
AT OIL TEMP Warning Light Display > INSPECTION">Go to Step 7.
7.CHECK TCM.
Read the data of «ATF Temperature Lamp» using the Subaru Select Monitor.
Is “ON” displayed?
AT OIL TEMP Warning Light Display > INSPECTION">Go to Step 8.
Perform the self-diagnosis of combination meter. Combination Meter System > OPERATION">
8.CHECK TCM.
Read the data of «ATF Temp.» using the Subaru Select Monitor.
Is the display 125°C or more?
AT OIL TEMP Warning Light Display > INSPECTION">Go to Step 9.
Replace the TCM. Transmission Control Module (TCM)">
9.CHECK ATF TEMPERATURE.
Check the real fluid temperature from the transmission case surface temperature.
Does it clearly differ from the «ATF Temp.» displayed on Subaru Select Monitor?
Perform the diagnosis according to DTC P0712. If there is no problem, perform the diagnosis according to DTC P0713.
When ATF temperature can be judged as actually high, perform the diagnosis again after the ATF temperature lowers.
Operation
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > AT OIL TEMP Warning Light DisplayOPERATIONThe AT OIL TEMP light illuminates or blinks, when the ATF temperature is high and malfunction occurs in ...
Other materials:
Top display setting
1. Perform the preparation steps according
to "Preparation for screen settings"
2. Operate the "
"
or "
" switch to
select the "Top Display" item. Then push
the
button.
3. Push the
button once more.
4. Select an item by operating the "
" or
"
" switc ...
List of diagnostic trouble code (dtc) List
POWER ASSISTED SYSTEM (POWER STEERING) (DIAGNOSTICS) > List of Diagnostic Trouble Code (DTC)LISTDTCItemContent of diagnosisNoteNoneWithout DTCNormal Subaru Select Monitor > INSPECTION">“Assist limitation” is displayed in the current data «EPS operating condition».Assist l ...
AUX
WARNING
Do not operate the player's controls
or connect the portable audio device
while driving. Doing so may result in
loss of control of your vehicle and
cause an accident or serious injury.
CAUTION
Do not leave portable audio device
in the vehicle. The temperature
inside the vehicle ...
