Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: General diagnostic table Inspection

Subaru Crosstrek Service Manual / Lan system (diagnostics) / General diagnostic table Inspection

LAN SYSTEM (DIAGNOSTICS) > General Diagnostic Table

INSPECTION

Item

Operation

Specifications

Note

YES

NO

Diagnostic code

DTC is displayed when inspecting all DTCs.

Perform the diagnosis according to DTC.

System is normal.

—

Speedometer

Faster vehicle speed than the actual speed is displayed.

VDC CM data may not be received.

System is normal.

Also, check vehicle speed pulse circuit.

Fuel gauge

Fuel is present, but displayed less than actual amount.

Communication error may be present.

System is normal.

Also, check the fuel gauge.

Fuel level warning light

Fuel is present, but the light illuminates.

Communication error may be present.

System is normal.

Also, check the fuel gauge.

Engine coolant temperature light

Engine coolant temperature light blinks in red and blue alternately.

Communication error may be present.

System is normal.

Check the engine coolant light related items.

[S], [I] or [S#] indicator

Blinking.

Communication error may be present.

System is normal.

Check the intelligent switch.

VDC indicator

Illuminating.

Communication error may be present.

System is normal.

Check that VDC is not operating.

VDC OFF indicator

Illuminating.

Communication error may be present.

System is normal.

Check that VDC is not OFF.

Brake warning, etc.

Illuminating.

Brake fluid may be low in amount, or communication error may be present.

System is normal.

Check brake related items.

Shift position

Not displayed.

Communication error may be present.

System is normal.

Also, check AT system.

AT temperature light

Blinking.

Communication error may be present.

System is normal.

Also, check AT system.

Door indicator

Not displayed.

Communication error may be present.

System is normal.

Check the door switch.

Clearance indicator

Not illuminating.

Communication error may be present.

System is normal.

Check the combination switch.

Hi beam indicator

Not illuminating.

Communication error may be present.

System is normal.

Check the combination switch.

Front fog indicator

Not illuminating.

Communication error may be present.

System is normal.

Check the combination switch.

Illumination

Illuminating at the maximum brightness.

Communication error may be present.

System is normal.

Also, check the illumination switch.

Cruise control indicator

Not illuminating.

Communication error may be present.

System is normal.

Check the cruise control system.

AWD indicator

Not illuminating.

Communication error may be present.

System is normal.

Check TCM.

Hill hold indicator

Not illuminating.

Communication error may be present.

System is normal.

Also, check VDC CM.

Electrical component location Location
LAN SYSTEM (DIAGNOSTICS) > Electrical Component LocationLOCATION(1)VDC CM(7)Combination meter(12)Data link connector(2)Power steering CM(8)A/C control panel(13)Transmission CM(3)Stereo camera(9)MFD ...

List of diagnostic trouble code (dtc) List
LAN SYSTEM (DIAGNOSTICS) > List of Diagnostic Trouble Code (DTC)LISTDTCItemContent of diagnosisNoteU1201CAN-HS COUNTER ABNORMALHigh speed CAN communication error Diagnostic Procedure with Diagnosti ...

Other materials:

Disarming the system
Perform either of the following procedures. Briefly press the disarm button (for less than 2 seconds) on the access key/remote transmitter. Carry the access key and perform either of the following procedures (models with "keyless access with push-button start system"). Grip the front door ...

Dtc p0617 starter relay "a" circuit high
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0617 STARTER RELAY "A" CIRCUIT HIGHDTC DETECTING CONDITION:Immediately at fault recognitionTROUBLE SYMPTOM:Failure of engine to startCAUTION:After servicing or replacing faulty parts, perform Clear ...

Active test Operation
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Active TestOPERATIONCAUTION:• Be sure to perform the active test while the engine is not running.• After executing the active test, execute the Clear Memory Mode.1. On «Start» display, select «Diagnosis».2. On «Vehicle selection ...

© 2016-2025 Copyright www.sucross.com