Subaru Crosstrek Service Manual: Dtc u0126 lost communication with steering angle sensor module

DTC DETECTING CONDITION:

No data is received from steering angle sensor.

TROUBLE SYMPTOM:

VDC CM does not operate normally.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0126 LOST COMMUNICATION WITH STEERING ANGLE SENSOR MODULE">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0126 LOST COMMUNICATION WITH STEERING ANGLE SENSOR MODULE">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is U0126 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0126 LOST COMMUNICATION WITH STEERING ANGLE SENSOR MODULE">Go to Step 4.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0126 LOST COMMUNICATION WITH STEERING ANGLE SENSOR MODULE">Go to Step 8.

4.CHECK DTC.

1) Check CAN communication circuit. CAN Communication Circuit Check">

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0126 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0126 LOST COMMUNICATION WITH STEERING ANGLE SENSOR MODULE">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0126 LOST COMMUNICATION WITH STEERING ANGLE SENSOR MODULE">Go to Step 8.

5.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the steering angle sensor data no-receive detected in several modules?

Replace the steering angle sensor. Steering Angle Sensor">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0126 LOST COMMUNICATION WITH STEERING ANGLE SENSOR MODULE">Go to Step 6.

6.REPLACE MODULE.

1) Replace the steering angle sensor.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0126 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0126 LOST COMMUNICATION WITH STEERING ANGLE SENSOR MODULE">Go to Step 7.

System is normal.

7.CHECK MODULE.

1) Reinstall the steering angle sensor.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0126 a current malfunction?

Replace the steering angle sensor. Steering Angle Sensor">

System is normal.

8.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0126 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0126 LOST COMMUNICATION WITH STEERING ANGLE SENSOR MODULE">Go to Step 9.

9.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Dtc u0122 lost communication with vehicle dynamics control module

Dtc u0131 lost communication with power steering control module

Other materials:

Procedure
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Learning ControlPROCEDURE1. PREPARATION FOR LEARNING1. Warm up or cool down until the ATF temperature displayed on the Subaru Select Monitor is 40 — 65°C (104 — 149°F).2. After stopping the vehicle, shift the select leve ...

Dtc p2757 torque converter clutch pressure control solenoid control circuit performance/stuck off
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2757 TORQUE CONVERTER CLUTCH PRESSURE CONTROL SOLENOID CONTROL CIRCUIT PERFORMANCE/STUCK OFFDTC detecting condition:Detected when two consecutive driving cycles with fault occur.Trouble ...

List
TELEMATICS SYSTEM (DIAGNOSTICS) > Read Current DataLISTDisplayContentReference valueUnitTrip Count [count]Refer to “LAN SYSTEM (DIAGNOSTICS)”. General Description > CAUTION"> — — Count — — Time Count [msec] — — Current GPS DataCurrent GPS information — †...