Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Procedure

CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Learning Control

PROCEDURE

1. PREPARATION FOR LEARNING

1. Warm up or cool down until the ATF temperature displayed on the Subaru Select Monitor is 40 — 65°C (104 — 149°F).

2. After stopping the vehicle, shift the select lever to “P” range.

3. Fully apply the parking brake.

4. Lift up the vehicle.

CAUTION:

While working, be sure to keep the lower edge of the tires 30 cm or more above the ground as vehicle will vibrate.

5. Connect the Subaru Select Monitor to data link connector.

6. Turn the ignition switch to ON.

7. Turn off all switches causing an electrical load, such as headlights, A/C, seat heater and rear defogger, etc.

2. SIMPLE LEARNING

NOTE:

Simple learning is performed with the vehicle lifted, without actually running the vehicle.

CAUTION:

Do not turn the power of the Subaru Select Monitor OFF during work, and do not disconnect the data link connector.

1. On «Start» display, select «Diagnosis».

2. On «Vehicle selection» display, input the vehicle information and select «Confirmed».

3. On «Main Menu» display, select «Each System».

4. On «Select System» display, select «Transmission Control System».

5. On «Select Function» display, select «Work Support».

6. On «Work Support» display, select «AT learning mode».

7. Follow the messages displayed on the screen when working.

NOTE:

During AT learning in progress, AT OIL TEMP light in the combination meter starts flashing at 2 Hz and the learning operation starts. The following message is displayed on the screen when the AT OIL TEMP light which was flashing at 2 Hz turns off.

8. When «AT learning normally ended.» is displayed, simple AT learning is completed.

NOTE:

If communication error occurs during learning, retry the “AT learning mode” from the beginning.

If the message «Execute AT learning again after fixing troubles of the vehicle» appears during learning, select [OK] and display the DTC list. After repairing the locations indicated by the DTC, start the “AT learning mode” over from the beginning.

When communication error occurs during learning, select lever does not shift occasionally. If select lever does not shift, turn the ignition switch to OFF before operating the select lever.

If the message «AT learning ended abnormally. Try again from the beginning.» is displayed, start the “AT learning mode” over from the beginning.

Display

Main causes for abnormal termination

AT learning ended abnormally. Try again from the beginning.

Fault is detected during AT learning.

The accelerator pedal is depressed during AT learning.

An unspecified operation was performed during AT learning

ATF temperature becomes out of specification during AT learning.

Battery voltage is low.

Malfunction indicator light illuminates.

Parking brake not applied strongly enough.

Brake pedal is not fully depressed.

Abnormal idle speed increase, etc.

For detailed operation procedures, refer to “Application help”.

Learning control
...

General description
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Learning ControlGENERAL DESCRIPTION• Follow the messages displayed on the Subaru Select Monitor when working.• When the following work ...

Other materials:

Operation
ENTERTAINMENT > Navigation SystemOPERATION1. SUBARU STARLINK CONNECTION ID DISPLAY1. Turn the ignition switch to ACC.2. Press the AUDIO/TUNE knob (b) five times with the HOME button (a) pressed to display the {Service Menu} screen.3. Touch the {Product Information} (c) to display the {Product Inf ...

Outside mirrors
Convex mirror (passenger side) WARNING Objects look smaller in a convex mirror and farther away than when viewed in a flat mirror. Do not use the convex mirror to judge the distance of vehicles behind you when changing lanes. Use the inside mirror (or glance backwards) to determine the actu ...

Type D
Temperature control dial (Refer to "Automatic climate control operation (type B, C and D)" F4-7 and/or "Temperature control Defroster button (Refer to "Airflow mode selection" Rear window defogger button (Refer to "Defogger and deicer" DUAL mode button (Refer to ""DUAL" mode ( ...

© 2016-2025 Copyright www.sucross.com