Subaru Crosstrek Service Manual: Dtc p2746 intermediate shaft speed sensor "b" circuit range/performance
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)
DTC P2746 INTERMEDIATE SHAFT SPEED SENSOR "B" CIRCUIT RANGE/PERFORMANCE
DTC detecting condition:
Immediately at fault recognition
Trouble symptom:
• Standing start problems
• Shock occurs when engaging the lockup clutch.
• Shock occurs when selecting shift position.
| STEP | CHECK | YES | NO |
1.CHECK DTC.
Read the DTC using Subaru Select Monitor.
Besides DTC P2746, is DTC P2747 or P2751 displayed?
Perform the diagnosis according to DTCs other than P2746.
Perform the diagnosis according to DTC P2747. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2747 INTERMEDIATE SHAFT SPEED SENSOR "B" CIRCUIT NO SIGNAL">
1. OUTLINE OF DIAGNOSIS
Diagnosis 1
• Detect the malfunction of primary speed sensor signal characteristics.
• Judge as NG if the primary speed, compared with the speeds of other parts, is outside the possible range considering the hardware capabilities.
Diagnosis 2
• Detect the malfunction of primary speed sensor signal characteristics.
• Judge as NG if the primary speed exceeds the predetermined value.
2. EXECUTION CONDITION
Secondary Parameters | Execution condition |
Diagnosis 1 | |
12 V battery system voltage | ≥ 9 V |
Transmission range | Drive or Reverse |
(Measured turbine shaft speed / Measured secondary pulley shaft speed) | ≥ 0.4 |
and | |
≤ 2.55 | |
Diagnosis 2 | |
12 V battery system voltage | ≥ 9 V |
Transmission range | Drive or Reverse |
(Measured turbine shaft speed / Measured secondary pulley shaft speed) | ≥ 0.4 |
and | |
≤ 2.55 |
3. DIAGNOSTIC METHOD
If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.
Malfunction Criteria | Threshold Value |
Diagnosis 1 | |
(Measured primary pulley shaft speed / Measured secondary pulley shaft speed) | < 0.36 |
or | |
> 2.80 | |
Diagnosis 2 | |
Measured primary pulley shaft speed | > 7140 rpm |
Time Needed for Diagnosis: 5 seconds
Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.
Dtc p160a random access memory (ram) error
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P160A RANDOM ACCESS MEMORY (RAM) ERRORDTC DETECTING CONDITION:Detected when two consecu ...
Dtc p2747 intermediate shaft speed sensor "b" circuit no signal
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2747 INTERMEDIATE SHAFT SPEED SENSOR "B" CIRCUIT NO SIGNALDTC detecting cond ...
Other materials:
Inspection
LIGHTING SYSTEM > Luggage Room LightINSPECTION1. LUGGAGE ROOM LIGHT BULB1. Visually check the bulb for blow out.2. Check the bulb specification. General Description > SPECIFICATION">3. Replace the bulb if it is found defective.2. LUGGAGE ROOM LIGHT SWITCH1. Check the resistance betwee ...
Installation
CLUTCH SYSTEM > Release Bearing and LeverINSTALLATIONNOTE:Apply the specified grease to lubricate to the following points before installation.• Contact surface of lever and pivot• Contact surface of lever and bearing• Transmission main shaft spline• Contact surface of rele ...
Removal
EXTERIOR/INTERIOR TRIM > Side GarnishREMOVAL1. Remove the clips and detach the side garnish assembly.(1)Garnish ASSY - fender(2)Garnish ASSY - rear quarter(3)Garnish ASSY - side sill2. Remove the garnish assembly or protector on the fender panel.CAUTION:Do not reuse the garnish assembly and prote ...
