Subaru Crosstrek Service Manual: Dtc p2006 tgv control stuck closed bank 1

Subaru Crosstrek Service Manual / Engine (diagnostics)(h4do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p2006 tgv control stuck closed bank 1

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P2006 TGV CONTROL STUCK CLOSED BANK 1

DTC DETECTING CONDITION:

Immediately at fault recognition

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

STEP	CHECK	YES	NO

1.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check the appropriate DTC using the “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2006 TGV CONTROL STUCK CLOSED BANK 1">Go to Step 2.

2.CHECK TUMBLE GENERATOR VALVE RH.

1) Remove the tumble generator valve assembly RH.

2) Check the tumble generator valve.

Is there any dirt or clogging with foreign objects in the tumble generator valve?

Clean the tumble generator valve.

Replace the tumble generator valve RH. Tumble Generator Valve Assembly">

1. OUTLINE OF DIAGNOSIS

Detect the malfunction of tumble generator valve motor function.

Judge close fixing malfunction when the opening degree is small even after finishing the tumble generator valve open driving.

2. EXECUTION CONDITION

Secondary Parameters	Execution condition
Battery voltage	≥ 10.9 V
Elapsed time of TGV commanded* to "open"	≥ 1600 ms

3. GENERAL DRIVING CYCLE

Always perform the diagnosis continuously.

4. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria	Threshold Value
TGV position	= Closed
As defined by: TGV angle position sensor voltage < 2.5 V

Malfunction Criteria

Threshold Value

TGV position

= Closed

As defined by:

TGV angle position sensor voltage < 2.5 V

Time Needed for Diagnosis: 3000 ms

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p2005 tgv control stuck open bank 2

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2005 TGV CONTROL STUCK OPEN BANK 2DTC DETECTING CONDITION:Immediately at fault recognitionCAUTION:After serv ...

Dtc p2007 tgv control stuck closed bank 2

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2007 TGV CONTROL STUCK CLOSED BANK 2DTC DETECTING CONDITION:Immediately at fault recognitionCAUTION:After se ...

Other materials:

Tripped sensor identification
The security indicator light flashes when the alarm system has been triggered. Also, the number of flashes indicates the location of unauthorized intrusion or the severity of impact on the vehicle. When the ignition switch is turned to the "ON" position, the indicator light will light for ...

Note
LIGHTING SYSTEM > Day Time Running Light SystemNOTEFor operation procedures of each component of the daytime running light system, refer to the respective section.• Headlight Assembly: Headlight Assembly">• Headlight bulb: Headlight Bulb">• Combination switch ( ...

Installation
BRAKE > Rear Disc RotorINSTALLATIONNOTE:Before installation, remove mud and foreign matter from the caliper body assembly.1. Before installation, check the rear disc rotor. Rear Disc Rotor > INSPECTION">2. Install each part in the reverse order of removal.NOTE:When installing the rear ...