Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc p0172 system too rich bank 1

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P0172 SYSTEM TOO RICH BANK 1

DTC detecting condition:

Detected when two consecutive driving cycles with fault occur.

Trouble symptom:

Improper idling

Engine stall

Poor driving performance

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

STEPCHECKYESNO

1.CHECK EXHAUST SYSTEM.

Are there holes or loose bolts on exhaust system?

Repair the exhaust system.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0172 SYSTEM TOO RICH BANK 1">Go to Step 2.

2.CHECK AIR INTAKE SYSTEM.

Are there holes, loose bolts or disconnection of hose on air intake system?

Repair the air intake system.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0172 SYSTEM TOO RICH BANK 1">Go to Step 3.

3.CHECK FUEL PRESSURE.

WARNING:

Place “NO OPEN FLAMES” signs near the working area.

CAUTION:

Be careful not to spill fuel.

Measure the fuel pressure. Fuel Pressure > INSPECTION">

CAUTION:

Release fuel pressure before removing the fuel pressure gauge.

Is the measured value 340 — 400 kPa (3.5 — 4.1 kg/cm2, 49 — 58 psi)?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0172 SYSTEM TOO RICH BANK 1">Go to Step 4.

Check the fuel pump and fuel delivery line. Fuel Pump > INSPECTION"> Fuel Delivery and Evaporation Lines > INSPECTION">

4.CHECK ENGINE COOLANT TEMPERATURE SENSOR.

1) Start the engine and warm up completely.

2) Read the value of «Coolant Temp.» using the Subaru Select Monitor or a general scan tool.

NOTE:

Subaru Select Monitor

For detailed operation procedures, refer to “Current Data Display For Engine”. Subaru Select Monitor">

General scan tool

For detailed operation procedures, refer to the general scan tool operation manual.

Is the value of «Coolant Temp.» 75°C (167°F) or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0172 SYSTEM TOO RICH BANK 1">Go to Step 5.

Replace the engine coolant temperature sensor. Engine Coolant Temperature Sensor">

5.CHECK MASS AIR FLOW AND INTAKE AIR TEMPERATURE SENSOR.

1) Start the engine and warm up engine until coolant temperature is higher than 75°C (167°F).

2) For CVT models, set the select lever to “P” range or “N” range, and for MT models, place the gear shift lever in the neutral position.

3) Turn the A/C switch to OFF.

4) Turn all the accessory switches to OFF.

5) Read the value of «Mass Air Flow» using the Subaru Select Monitor or a general scan tool.

NOTE:

Subaru Select Monitor

For detailed operation procedures, refer to “Current Data Display For Engine”. Subaru Select Monitor">

General scan tool

For detailed operation procedures, refer to the general scan tool operation manual.

Is the value of «Mass Air Flow» 2.0 — 5.0 g/s (0.26 — 0.66 lb/m)?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0172 SYSTEM TOO RICH BANK 1">Go to Step 6.

Replace the mass air flow and intake air temperature sensor. Mass Air Flow and Intake Air Temperature Sensor">

6.CHECK MASS AIR FLOW AND INTAKE AIR TEMPERATURE SENSOR.

1) Start the engine and warm up engine until coolant temperature is higher than 75°C (167°F).

2) For CVT models, set the select lever to “P” range or “N” range, and for MT models, place the gear shift lever in the neutral position.

3) Turn the A/C switch to OFF.

4) Turn all the accessory switches to OFF.

5) Open the front hood.

6) Measure the ambient temperature.

7) Read the value of «Intake Air Temp.» using the Subaru Select Monitor or a general scan tool.

NOTE:

Subaru Select Monitor

For detailed operation procedures, refer to “Current Data Display For Engine”. Subaru Select Monitor">

General scan tool

For detailed operation procedures, refer to the general scan tool operation manual.

Subtract ambient temperature from «Intake Air Temp.». Is the obtained value −10 — 50°C (−18 — 90°F)?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0172 SYSTEM TOO RICH BANK 1">Go to Step 7.

Check the mass air flow and intake air temperature sensor. Mass Air Flow and Intake Air Temperature Sensor">

7.CHECK PCV VALVE.

Check the PCV valve.

Check that the PCV valve has no deformation, cracks or other damages.

Repair or replace the PCV valve.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0172 SYSTEM TOO RICH BANK 1">Go to Step 8.

8.CHECK PCV HOSE.

Check the PCV hose.

Check the PCV hose assembly for cracks, damage or looseness.

Repair or replace the PCV hose.

Repair the poor contact of ECM connector.

1. OUTLINE OF DIAGNOSIS

Detect fuel system malfunction by the amount of main feedback control.

2. EXECUTION CONDITION

Secondary parameters

Execution condition

Main feedback

In operation

3. GENERAL DRIVING CYCLE

Perform the diagnosis continuously during the closed loop.

4. DIAGNOSTIC METHOD

Compare the diagnostic value with the threshold value, and if a condition meeting the malfunction criteria listed below continues for 10 s ? 3 time(s) or more, judge that there is a fault in the fuel system.

Judgment value

Malfunction Criteria

Threshold Value

Offset amount of main feedback compensation

< Value from Map

Map

Warm-up increase compensation coefficient

0

0.1

0.2

0.3

Threshold Value

0.67

0.572

0.494

0.432

Warm-up increase compensation coefficient

0.35

0.6

Threshold Value

0.401

0.401

Time needed for diagnosis: 10 s ? 3 time(s)

Malfunction indicator light illumination: Illuminates when malfunction occurs in 2 continuous driving cycles.

Dtc p0171 system too lean bank 1
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0171 SYSTEM TOO LEAN BANK 1Refer to DTC P0172 for diagnostic procedure. Diagnostic Procedure with Diagnosti ...

Dtc p0196 engine oil temperature sensor "a" range/performance
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0196 ENGINE OIL TEMPERATURE SENSOR "A" RANGE/PERFORMANCEDTC DETECTING CONDITION:Detected when two ...

Other materials:

Dtc u0416 invalid data received from vehicle dynamics control module
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0416 INVALID DATA RECEIVED FROM VEHICLE DYNAMICS CONTROL MODULENOTE:For the diagnostic procedure, refer to LAN section. Basic Diagnostic Procedure">1. OUTLINE OF DIAGNOSISDetect malfunction of CAN co ...

Dtc b228a engine speed signal(with auto start stop)
KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B228A ENGINE SPEED SIGNAL(WITH Auto Start Stop)DTC detecting condition:When the engine speed signal transmitted from the ECM via solid line and the engine speed signal transmitt ...

Auto light sensor sensitivity setting
1. Perform the preparation steps according to "Preparation for car settings" 2. Operate the " " or " " switch to select the "Auto Light Sensor" item. Then push the   button. 3. The current setting will be displayed. Push the button to enter the selection mode. 4. Selec ...

© 2016-2024 Copyright www.sucross.com