Subaru Crosstrek Service Manual: Dtc p0024 "b" camshaft position - timing over-advanced or system performance bank 2

DTC detecting condition:

Detected when two consecutive driving cycles with fault occur.

Trouble symptom:

• Engine stall

• Improper idling

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

1.IDENTIFYING FAULTY PART.

1) Perform the Clear Memory Mode. Clear Memory Mode">

2) Replace the defective oil control solenoid by the other (RH or LH, intake side or exhaust side) oil control solenoid.

3) Perform appropriate drive cycle test. Drive Cycle">

4) Make sure that the fault occurrence (DTC and incorrect advancing) has shifted to the other location.

Did the detected DTC shift to the location where the oil control solenoid was replaced?

Replace the faulty oil control solenoid.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0024 "B" CAMSHAFT POSITION - TIMING OVER-ADVANCED OR SYSTEM PERFORMANCE BANK 2">Go to Step 2.

2.CHECK CURRENT DATA.

1) Start the engine and let it idle.

2) Read the value of «Exh. VVT Retard Ang. L» using the Subaru Select Monitor.

NOTE:

For detailed operation procedures, refer to “Current Data Display For Engine”. Subaru Select Monitor">

Is the value of «Exh. VVT Retard Ang. L» approx. 0 deg?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0024 "B" CAMSHAFT POSITION - TIMING OVER-ADVANCED OR SYSTEM PERFORMANCE BANK 2">Go to Step 3.

Check the following item and repair or replace if necessary.

• Exhaust cam sprocket (clog or dirt of oil routing, setting of spring)

• Exhaust camshaft (dirt, damage of camshaft)

3.CHECK CURRENT DATA.

1) Drive with acceleration and deceleration at 80 km/h (50 MPH) or less.

NOTE:

Drive to an extent that the duty output of oil flow control solenoid valve increases.

2) Read the values of «Exh. OCV Duty L» and «Exh. VVT Retard Ang. L» using the Subaru Select Monitor.

NOTE:

For detailed operation procedures, refer to “Current Data Display For Engine”. Subaru Select Monitor">

When the value of «Exh. OCV Duty L» increases more than 10%, is the value of «Exh. VVT Retard Ang. L» approx. 0 deg?

Check the following item and repair or replace if necessary.

• Exhaust cam sprocket (clog or dirt of oil routing, setting of spring)

• Exhaust camshaft (dirt, damage of camshaft)

Perform the following procedures, and clean the oil routing.

Replace the engine oil and idle the engine for 5 minutes, and then replace the oil filter and engine oil. Engine Oil > REPLACEMENT"> Engine Oil Filter">

For the detection standard, refer to DTC P0014. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0014 "B" CAMSHAFT POSITION - TIMING OVER-ADVANCED OR SYSTEM PERFORMANCE BANK 1">

Dtc p0023 "b" camshaft position actuator control circuit/open bank 2

Dtc p0030 a/f / o2 heater control circuit bank 1 sensor 1

Other materials:

Inspection
BODY CONTROL SYSTEM (DIAGNOSTICS) > General DescriptionINSPECTIONBefore performing diagnosis, check the following items which might affect body control system problems.1. Check the battery. Battery">2. Check the fuse condition.Make sure that ampere of the fuse is setting value, and it is ...

Inspection
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF) > SunshadeINSPECTION1. MOVING LOAD OF SUNSHADE ASSEMBLY1. Attach a spring scale together with a cloth to the edge of sunshade assembly.2. Pull the spring scale to check the moving load of the sunshade assembly.Moving load of sunshade assembly:14±6 N (1.43 ...

Component
MECHANICAL(H4DO) > General DescriptionCOMPONENT1. TIMING CHAIN(1)Intake camshaft RH(8)Chain tensioner RH(15)Exhaust camshaft LH(2)Exhaust camshaft RH(9)Crank sprocket (3)Intake cam sprocket RH(10)O-ringTightening torque: N·m (kgf-m, ft-lb)(4)Exhaust cam sprocket RH(11)Chain tensioner LHT1 ...