Subaru Crosstrek Service Manual: Dtc c1423 different ecu specifications

DTC detecting condition:

Different control module specification

Trouble symptom:

• ABS does not operate.

• VDC does not operate.

• Hill start assist does not operate.

When parameter selection for VDCCM is improper, this DTC may be memorized.

1.CHECK VDCCM&H/U IDENTIFICATION SYMBOL.

Check the identification symbol attached on the H/U. General Description > SPECIFICATION">

Is the identification symbol correct?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS">Go to Step 2.

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

2.CHECK PARAMETER SELECTED IN VDCCM.

Subaru Select Monitor > OPERATION">

Does the parameter registered in the VDCCM match the relevant vehicle?

CVT model: Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS">Go to Step 3.
MT model: Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS">Go to Step 5.

Select and register the correct parameter. Subaru Select Monitor > OPERATION">

3.CHECK TCM SPECIFICATION.

Check the TCM specification.

Is the specification of TCM same as vehicle specification?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS">Go to Step 4.

Replace the TCM. Transmission Control Module (TCM)">

4.CHECK CVT SYSTEM.

1) Start the engine.

2) Read the DTC of the CVT system. Read Diagnostic Trouble Code (DTC)">

Is DTC of CVT system displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS">Go to Step 5.

5.CHECK ECM SPECIFICATION.

Check the ECM specification.

Is the specification of ECM same as vehicle specification?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS">Go to Step 6.

Replace the ECM. Engine Control Module (ECM)">

6.CHECK ENGINE SYSTEM.

1) Start the engine.

2) Read DTC of the engine system. Read Diagnostic Trouble Code (DTC)">

Is engine system DTC displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS">Go to Step 7.

7.CHECK VDCCM&H/U.

1) Perform the Clear Memory Mode. Clear Memory Mode">

2) Perform the Inspection Mode. Inspection Mode">

3) Read the DTC. Read Diagnostic Trouble Code (DTC)">

Is the same DTC displayed?

Replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1423 DIFFERENT ECU SPECIFICATIONS">Go to Step 8.

8.CHECK DETECTION OF OTHER DTCS FOR VDC.

Read Diagnostic Trouble Code (DTC)">

Is any other DTC displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.

Dtc c1432 different ecu specifications

Dtc c1731 g sensor abnormal

Other materials:

Removal
BRAKE > Front Brake PadREMOVAL1. Lift up the vehicle, and then remove the front wheels.2. Remove the front brake pad.(1) Remove the caliper bolt on the lower side.(2) Raise the caliper body assembly and support it.NOTE:Do not disconnect the brake hose from the caliper body assembly.(3) Remove the ...

Disassembly
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Reverse Brake AssemblyDISASSEMBLY1. Remove the snap ring.2. Remove the retaining plate, drive plate, driven plate and dish plate.3. Compress the return spring using the ST to remove the snap ring.ST 18762AA001COMPRESSOR SPECIAL TOOL4. Using the ST, r ...

Installation
AIRBAG SYSTEM > Roll ConnectorINSTALLATIONCAUTION:If the steering wheel and steering angle sensor (steering roll connector) are removed, be sure to perform the following operations.• Align the center position of the steering roll connector.• Perform the neutral position setting of the ...