Subaru Crosstrek Service Manual: Dtc c0074 master cylinder pressure sensor output

DTC detecting condition:

Defective pressure sensor

Trouble symptom:

• ABS does not operate.

• VDC does not operate.

• EyeSight does not operate.

1.CHECK STOP LIGHT SWITCH CIRCUIT.

Check stop light switch open circuit.

Is the check result OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0074 MASTER CYLINDER PRESSURE SENSOR OUTPUT">Go to Step 2.

Repair the stop light switch circuit.

NOTE:

If there is malfunction in the stop light circuit, DTC may be recorded in the memory.

2.CHECK OUTPUT OF PRESSURE SENSOR WITH SUBARU SELECT MONITOR.

1) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

2) Read the «Master Cylinder Pressure Sensor» displayed on display.

With the brake pedal released, does the value for «Master Cylinder Pressure Sensor» fall within 0 — 11 bar?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0074 MASTER CYLINDER PRESSURE SENSOR OUTPUT">Go to Step 3.

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

3.CHECK OUTPUT OF PRESSURE SENSOR WITH SUBARU SELECT MONITOR.

1) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

2) Read the «Master Cylinder Pressure Sensor» displayed on display.

When the brake pedal is operated, does the value of «Master Cylinder Pressure Sensor» change in accordance with the brake pedal?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0074 MASTER CYLINDER PRESSURE SENSOR OUTPUT">Go to Step 4.

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

4.CHECK VDCCM&H/U.

1) Perform the Clear Memory Mode. Clear Memory Mode">

2) Perform the Inspection Mode. Inspection Mode">

3) Read the DTC. Read Diagnostic Trouble Code (DTC)">

Is the same DTC displayed?

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0074 MASTER CYLINDER PRESSURE SENSOR OUTPUT">Go to Step 5.

5.CHECK DETECTION OF OTHER DTCS FOR VDC.

Read Diagnostic Trouble Code (DTC)">

Is any other DTC displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.

Dtc c0071 no signal from steering angle sensor

Dtc c0075 wheel cylinder pressure sensor output

Other materials:

Removal
ENTERTAINMENT > External Connection TerminalREMOVAL1. Disconnect the ground cable from battery and wait for at least 60 seconds before starting work. NOTE">2. Remove the console box assembly. Console Box > REMOVAL">3. While pressing the claw, press it in from the rear to remo ...

Removal
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES)(H4DO) > Leak Check Valve AssemblyREMOVAL1. Disconnect the ground cable from battery.2. Lift up the vehicle.3. Remove the rear exhaust pipe. Rear Exhaust Pipe > REMOVAL">4. Remove the propeller shaft. Propeller Shaft > REMOVAL"& ...

Inspection
CONTROL SYSTEMS > Select CableINSPECTIONCheck the removed cable and replace or adjust if damaged, rusty or malfunctioning.1. Check the cable for smooth operation.2. Check the inner cable for damage and rust.3. Check the outer cable for damage, bends and cracks.4. Check the boot for damage, cracks ...