Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc c0046 body integrated module communication circuit

VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC C0046 BODY INTEGRATED MODULE COMMUNICATION CIRCUIT

DTC detecting condition:

No CAN signal received from body integrated unit.

Trouble symptom:

VDC may not operate.

Hill start assist does not operate.

STEPCHECKYESNO

1.CHECK LAN SYSTEM.

Perform the diagnosis for LAN system. Basic Diagnostic Procedure">

Is there any fault in LAN system?

Perform the diagnosis according to DTC for LAN system. List of Diagnostic Trouble Code (DTC)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0046 BODY INTEGRATED MODULE COMMUNICATION CIRCUIT">Go to Step 2.

2.CHECK POOR CONTACT OF CONNECTORS.

Is there poor contact of body integrated unit connector?

Repair the connector.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0046 BODY INTEGRATED MODULE COMMUNICATION CIRCUIT">Go to Step 3.

3.CHECK BODY INTEGRATED UNIT.

Perform the diagnosis for body integrated unit. Basic Diagnostic Procedure">

Is the check result OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0046 BODY INTEGRATED MODULE COMMUNICATION CIRCUIT">Go to Step 4.

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

4.CHECK VDCCM&H/U.

1) Connect all connectors.

2) Perform the Clear Memory Mode. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. Read Diagnostic Trouble Code (DTC)">

Is the same DTC displayed?

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0046 BODY INTEGRATED MODULE COMMUNICATION CIRCUIT">Go to Step 5.

5.CHECK DETECTION OF OTHER DTCS FOR VDC.

Read Diagnostic Trouble Code (DTC)">

Is any other DTC displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.

Dtc c1811 system
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C1811 SYSTEMDTC detecting condition:ABS and VDC long time sequential controlTrouble symptom ...

Dtc c0049 cruise controller abnormal
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C0049 CRUISE CONTROLLER ABNORMALDTC detecting condition:Faulty signal is received from the ...

Other materials:

Seatbelt pretensioners
The Subaru Ascent is equipped with advanced seatbelt pretensioner systems that significantly enhance occupant protection in the event of a collision. These systems are designed to instantly tighten the seatbelt, reducing slack and ensuring that passengers are securely restrained at the moment ...

Inspection
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Secondary Speed SensorINSPECTION1. Set the ST between the TCM and bulkhead harness.ST 18460AA040CHECK BOARD2. Set the probe of oscilloscope to the check board connector.Connector & terminalNo. 13 (+) — No. 42 (−):(A)+ probe(B)− prob ...

Dtc c0051 valve relay
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C0051 VALVE RELAYDTC detecting condition:Defective valve relayTrouble symptom:• ABS does not operate.• EBD does not operate.• VDC does not operate.• EyeSight does not ...

© 2016-2026 Copyright www.sucross.com