Subaru Crosstrek Service Manual: Dtc b2a05 left speaker/audio circuit

Diagnosis start condition:

When ACC is ON.

DTC detecting condition:

Speaker impedance is more than 10 k? for 100 ms. (Detached speaker connection, etc.)

Trouble symptom:

• Call function cannot be used.

• RED LED illuminates.

For the coupling connector, refer to “WIRING SYSTEM”.

CommCheck is required after replacing the DCM. Telematics System > OPERATION">

1.CHECK DTC.

Read the DTC. Diagnostic Code(s) Display">

Is DTC B2A05 displayed? (Current malfunction)

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A05 LEFT SPEAKER/AUDIO CIRCUIT">Go to Step 2.

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2.PERFORM THE SYSTEM OPERATION CHECK.

Perform [Speaker ON] in the system operation check mode. System Operation Check Mode">

Does it sound?

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A05 LEFT SPEAKER/AUDIO CIRCUIT">Go to Step 3.

3.CHECK HARNESS (OPEN CIRCUIT).

1) Turn the ignition switch to OFF.

2) Disconnect the speaker connector and tweeter connector.

3) Disconnect the DCM connector.

4) Measure the resistance between speaker connector and tweeter connector and DCM connector.

Connector & terminal

(i271) No. 2 — (D2) No. 2:
(i271) No. 2 — (i158) No. 1:
(i271) No. 10 — (D2) No. 1:
(i271) No. 10 — (i158) No. 3:

Is the resistance 1 ? or less?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A05 LEFT SPEAKER/AUDIO CIRCUIT">Go to Step 4.

Repair or replace the open circuit of harness.

4.CHECK HARNESS (GROUND SHORT CIRCUIT).

Measure the resistance between DCM connector and chassis ground.

Connector & terminal

(i271) No. 2 — Chassis ground:
(i271) No. 10 — Chassis ground:

Is the resistance 1 M? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A05 LEFT SPEAKER/AUDIO CIRCUIT">Go to Step 5.

Repair or replace the short circuit of the harness.

5.CHECK THE CONNECTOR (SHORT CIRCUIT TO POWER SUPPLY).

Measure the voltage between DCM connector and chassis ground.

Connector & terminal

(i271) No. 2 (+) — Chassis ground (−):
(i271) No. 10 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A05 LEFT SPEAKER/AUDIO CIRCUIT">Go to Step 6.

Repair or replace the short circuit of the harness.

6.CHECK THE SPEAKER.

Perform the inspection of speaker unit and tweeter unit. Front Speaker"> Rear Speaker">

Are the speaker and tweeter OK?

Replace the DCM. Data Communication Module">

Replace the speaker and tweeter. Front Speaker"> Rear Speaker">

Dtc b2a04 mic circuit

Dtc b2a06 right speaker/audio circuit

Other materials:

Basic diagnostic procedure Procedure
ENGINE (DIAGNOSTICS)(H4DO) > Basic Diagnostic ProcedurePROCEDURE1. ENGINESTEPCHECKYESNO1.CHECK ENGINE START FAILURE.1) Ask the customer when and how the trouble occurred using the interview check list. Check List for Interview > CHECK">2) Start the engine.Does the engine start? Basic ...

Installation
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES)(H4DO) > EGR CoolerINSTALLATION1. Set the gasket to the stud bolt.NOTE:Use a new gasket.2. Temporarily tighten the bolts securing the EGR cooler to the EGR control valve and the cylinder head RH, and tighten in numerical order.NOTE:Use a new gasket. ...

Note
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Air Conditioning SystemNOTEFor procedure of each component in the air conditioning system, refer to the respective section.• Blower motor unit assembly: Blower Motor Unit Assembly">• Blower motor: Blower Motor">• Power ...