Subaru Crosstrek Service Manual: Dtc b1836 open in curtain airbag lh squib circuit

Diagnosis start condition:

Ignition voltage is 10 V to 16 V.

DTC detecting condition:

• Curtain airbag harness (LH) circuit is open.

• Curtain airbag module (LH) is faulty.

• Airbag control module is faulty.

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">

1.CHECK POOR CONTACT OF CONNECTORS.

Check for poor contact of the connectors between the airbag control module, curtain airbag module LH and the curtain airbag sensor LH.

Is there poor contact?

Replace the airbag rear harness along with body harness.

Diagnostic Chart with Trouble Code > DTC B1836 OPEN IN CURTAIN AIRBAG LH SQUIB CIRCUIT">Go to Step 2.

2.CHECK CURTAIN AIRBAG MODULE.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB31) from curtain airbag module (LH).

3) Connect the connector (1N) in the test harness N to the connector (AB31).

4) Connect the airbag resistor to the connector (2N) of test harness N.

5) Connect the battery ground terminal and turn the ignition switch to ON.

Does the airbag warning light illuminate for 6 seconds and go off?

Replace the curtain airbag module (LH). Curtain Airbag Module">

Diagnostic Chart with Trouble Code > DTC B1836 OPEN IN CURTAIN AIRBAG LH SQUIB CIRCUIT">Go to Step 3.

3.CHECK AIRBAG REAR HARNESS (CURTAIN AIRBAG MODULE HARNESS LH).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB21) from seat belt pretensioner (LH).

3) Disconnect connector (AB19) from side airbag module (LH).

4) Disconnect the airbag resistor from test harness N.

5) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.

6) Connect the connector (1AG) in the test harness AG to the connectors (AB6, AB17, AB18).

7) Measure the resistance between connector (6AG) in the test harness AG and connector (2N) in the test harness N.

Connector & terminal

(6AG) No. 1 — (2N) No. 2:
(6AG) No. 3 — (2N) No. 1:

Is the resistance less than 10 ??

Diagnostic Chart with Trouble Code > DTC B1836 OPEN IN CURTAIN AIRBAG LH SQUIB CIRCUIT">Go to Step 4.

Replace the airbag rear harness along with body harness.

4.CHECK AIRBAG CONTROL MODULE.

1) Connect all connectors.

2) Clear the memory. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">

Is DTC B1836 displayed?

Replace the airbag control module. Airbag Control Module">

Diagnostic Chart with Trouble Code > DTC B1836 OPEN IN CURTAIN AIRBAG LH SQUIB CIRCUIT">Go to Step 5.

5.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Finish the diagnosis.

Dtc b1835 short in curtain airbag lh squib circuit

Dtc b1837 short in curtain airbag lh squib circuit (to ground)

Other materials:

USB power supply
CAUTION In the Subaru Ascent, only USB Type-A and Type-C terminals are supported. Connecting devices with incompatible connectors may result in charging failure or device malfunction. There is always a possibility of device malfunction or data loss when using USB connections. Any conn ...

Removal
INTAKE (INDUCTION)(H4DO) > Air Intake BootREMOVAL1. Remove the clip (A) from the air intake boot.2. Loosen the clamp (B) securing the air cleaner case (rear) to the air intake boot.3. Loosen the clamp (C) which secures the throttle body to the air intake boot.4. Disconnect the PCV hose and remove ...

Windshield wipers
Mist (for a single wipe) Off Intermitten Low speed High speed To turn the wipers on, push the wiper control lever down. To turn the wipers off, return the lever to the " " position. For a single wipe of the wipers, push the lever up. The wipers operate until you release the lever. ...